Skill Builder: Making A Butterfly Spline (Or “Arikata”)

Woodworking
Skill Builder: Making A Butterfly Spline (Or “Arikata”)

We asked Make: contributor Len Cullum to contribute some pieces on understanding basic woodworking tools and techniques. In this article, he outlines the process for making the butterfly spline, known in Japanese as “arikata. — Gareth

When working with wider, thicker slabs of wood, it is not uncommon to have checking (cracks) in the surface, particularly at the ends. While there are a couple of ways of dealing with this such as filling the gaps with wood or putties or epoxy, I prefer to leave it as it is, treating it as a feature instead of a flaw. A bit of honesty about the nature of wood perhaps. But in order to be sure the checking doesn’t continue, it needs to be stabilized. A simple way to do this is to add an “arikata” or butterfly spline. Not only does this method keep the check from widening and lengthening, it also visually addresses the crack, showing that it was left open with intent. Arikata are fairly easy to execute and the end results look pretty cool.

What We’ll Be Using:

  • Cracked piece – Port Orford Cedar
  • Spline piece – 1″ x 2″ x 3/8″ cherry
  • Sharp chisels – 1/2″ and 1″
  • Marking knife
  • Sharp Pencil
  • Router with 1/4″ straight bit
  • Adjustable square
  • Angle gauge
  • Hammer
  • Glue and brush

The first thing you will want to determine is how many splines you need. Since I am a form-follows-function kind of guy, I try to use as few as possible, maybe one for every three to five inches of checking. Next, decide the size. Again, since I am driven by function, I like to keep them as small as possible while still doing their job. I’ll often cut a couple out of paper and lay them on the piece to find the right size. I have made them as small as 1/2″ x 1″ up to 1 1/2″ x 3″. When it comes to thickness, you want to keep it on the thin side, between 1/4″ – 1/2″. It doesn’t require any more than that to keep a check from running and more importantly, if you are using a different type of wood for the spline it might have a dissimilar shrink/swell rate. This is especially true when using exotics like ebony or cocobolo. The thinner you make the spline, the less likely it will stand proud of the surface part of the year, and below it the rest. So enough talk, lets get it on.





Start with making the spline. I’m using a piece of cherry measuring 1″ wide 2″ long and 3/8″ thick (it’s important that the grain runs the length of the long dimension). Using an adjustable square, I mark the center of its length, and then 1/4″ in from each side. Then, using an angle gauge (I knew I forgot something in the layout tools article), draw lines from the outer corners to the center marks.





There are a few different ways to cut them out, from scroll saws to table saws, but if I only need a couple, I find this approach to be the quickest. First, I make a cut along the center line to where the angled lines meet. This is a relief cut that will make it easier to chisel out the waste. Being careful to keep your chisel flat, take a few small shavings down one slope, then rotate and take a few from the other side. Continue taking shavings from each side until both are down to the line. Working from both directions like this helps to minimize damage if the chisel overshoots and gouges the other side. Now flip and repeat.



Once the spline is cut, determine its position along the check. For greatest strength, try to align the centerline of the spline with the line of the check. When you have it where you like it, using a sharp pencil, carefully trace the spline. Trace it only once; going over it twice will only give you fuzzy lines that will be harder to work to. If you are working on dark wood, where pencil lines are hard to see, cover the area with a wide strip of masking tape and mark on it. Before taking the spline away, put an ‘X’ on one end and a corresponding mark on the board to keep track of splines orientation. Since it’s cut by hand, each side will be slightly different and it will only fit one way.




At this point you’re ready to start “wasting” the mortise. While I could just chop it out with the chisels or use a drill press, I prefer a router. The router gives me a quick, flat bottomed hole to the exact depth I need. Because I want the spline to stand proud of the surface so it can be flushed later, I set the router bit about 1/32 below the thickness of the spline. Route the mortise staying about 1/16″ in from the pencil lines. It’s tempting to try to get closer to the line. Don’t. One little slip up can send you back to the start to make a bigger spline.




Now that the hole has been wasted, begin carefully chiseling to the lines at the ends and along one side. To get a good fit it’s important that you only trim to one side. Take light, thin shavings and sneak up to the lines trying not to chisel them away. Once that is done, put the spline in the mortise and check the fit along the chiseled edges. If you notice any gaps, try to correct them now.




If it all looks good, use a marking knife to scribe lines along the unchiseled side. As with the pencil, only make one pass with the knife. When you pull the spline away you should be able to see why you chisel out one side at a time. The lines you scribed are usually inside of the pencil lines. Now chisel out the rest being very careful to work right up to the scribe lines. When all of the waste has been chiseled away, check the fit one more time. Only push the spline in a little way. If you push it too deep you might not be able to get it out. Trust that this is a lesson better read than experienced.


If the fit is good, carefully pull it out. Using a knife or chisel, chamfer (bevel) the inside edges of the spline. This will help it slide in straighter, keep from damaging the edges of the mortise and leave a little clearance in the corners for glue squeeze-out.





Using a small brush, apply a thin layer of glue to all of the surfaces of the mortise and to the bottom of the spline. I usually don’t glue the sides of the spline because it all gets peeled off when it’s being driven in. And less glue to clean up is less glue to clean up (’nuff said). Put the spline in the mortise and using a scrap to protect the surfaces, tap it in with a hammer. Listen as you tap it, the sounds it makes will tell you how deep you are and when you’ve reached the bottom.

If everything went well, the spline should be just proud of the surface and tight around the edges. When the glue has dried, all that’s left is to make the spline flush. This can be done by sanding or planing. If you decide to sand, be careful not to over sand the area around the spline, especially if the spline is harder wood that the board. It’s easy to make a donut-shaped hollow all around the spline. If planing, be sure to skew (hold plane diagonal to direction of cut) as you pass over the spline to help avoid tear-out.




And there you have it. A simple but cool little joint. This technique can also be used for joining boards together for tabletops etc. If a gap is desired, keep a thin piece of wood clamped between the boards while cutting the joint and then remove it before assembly.


Bio: Len Cullum is a woodworker living in Seattle, WA. He specializes in building Japanese-style garden structures and architectural elements. It was a picture of a wooden kayak in the summer of 1992 that set him on the path he remains on today. The desire to build one, and the fear of it sinking, are what drove him to learn finer woodworking skills. After eighteen years of brushing up on those skills, and building lots of other things, he still hasn’t attempted that kayak.

15 thoughts on “Skill Builder: Making A Butterfly Spline (Or “Arikata”)

  1. Anonymous says:

    Nice to see wood projects that don’t necessarily involve major power tools. And nice to see such detailed instruction. Good Stuff!

  2. Scott Saunders says:

    Very nice article. Thank you.

    I have some questions about sourcing and sizing wood that maybe you can answer (here or in a future article). I’d like to make a small table about 30in by 18in out of “real wood” not plywood. Home Depot has oak and poplar 1x10s and 1x12s. Can I piece those together to get my 18in width? What’s the best way to do that? Is there a way to put boards together and get a flat surface without a wide electric planer? Is there a better place to buy wood that might have 18in wide boards?

    I thought of this when I read the “Spline piece – 1″ x 2″ x 3/8″ cherry” in your parts list. I thought “Where do I get a 3/8″ thick piece of cherry?” Hopefully you can see where I’m coming from.

    Thanks again for a great article.

    1. Anonymous says:

      Hi Scott,
      Glad you liked the article. While 18″ wide stock can be found, it is not common. Most stock will max out at 11 1/2″, especially at home centers. If you want to use a single piece for the top I would suggest looking for a hardwood supplier in your area. Gluing up a top from multiple pieces is pretty straight forward though. Look for the straightest, flattest pieces you can find, ones that don’t cup (warping across the grain) and especially ones that don’t twist. This will probably limit you to the 6 – 8 inch wide stock, but who knows, you might get lucky with some wider stuff. Cupping can be dealt with but twisted boards are a real pain. Orient the boards how you would like them and then either number them or mark them in some other way to keep track. Some people draw a big triangle covering all of the boards to keep them straight. All that’s left is to run a bead of wood glue between each one and clamp them together. Use just enough clamping pressure to get glue to squeeze out and for the joints to close, but not so much that the boards are distorting. If there is enough material, cut all of the pieces larger than you need and then cut the glued up piece down to size. This will make everything much cleaner. Let me see… oh yeah, clean up as much of the glue as you can when it’s in it’s rubbery state (about twenty-thirty minutes in). You could wipe it with a damp cloth when it’s still wet, but I always find that to create more of a mess. Take your time and make sure everything is staying flat as you adjust you clamps and you should do okay. Good luck!

      The 3/8″ cherry is just scrap wood I had lying around. You can often find thinner stock like that at hardwood suppliers and hobby shops or you can always cut your own.

      Hope this helps

      1. matthewecross says:

        One important tip I’ve learned: if look at the end grain of your boards, unless the board is cut from the center of the tree you will see the grain curve up or down. When gluing up a series of boards, alternate the curve. If you glue them up with all of the curves going the same way, the glued up piece is likely to cup in the direction eventually, if you alternate them it is less likely to.

        Also, for extra strength you can join them pieces with biscuits (using a biscuit joiner) in addition to gluing them.

        1. Scott Saunders says:

          Thanks for the advice guys.

  3. Anonymous says:

    So do you attempt to fill the gap, Len?

    1. Anonymous says:

      No, I prefer to leave it as is. If this were an actual furniture piece, I would clean the loose fibers out the gap and then make sure to get some finish down inside.

  4. Chris Glatz says:

    Awesome tutorial.  With that trim router, how did you plunge into the cut?  Did you lower it in using the depth adjustment?

  5. Chris Glatz says:

    Awesome tutorial.  With that trim router, how did you plunge into the cut?  Did you lower it in using the depth adjustment?

  6. Best of MAKE: Skill Builders says:

    […] Making A Butterfly Spline (Or “Arikata”) from Woodworking month (February) […]

  7. MAKE | Workshop: Len Cullum in Seattle, Washington says:

    […] Making a Butterfly Spline (or “Arikata”) […]

  8. ○DIY/Tip▶ Workshop: Len Cullum in Seattle, Washington « dot dot dob tob tob says:

    […] Making a Butterfly Spline (or “Arikata”) […]

  9. Butterflies in Wood: A Tradition + Trend Coming Back | homedesignmagz.com says:

    […] to try making your own? Check out these two tutorials to […]

  10. Project: Entry Table | This Sporadic Life says:

    […] a butterfly joint before and had to do quite a bit of research.  Len Cullum’s tutorial on Makezine.com was super helpful.  The basic idea is that you make butterfly wedges so that the grain of your […]

Comments are closed.

Discuss this article with the rest of the community on our Discord server!
Tagged

Gareth Branwyn is a freelance writer and the former Editorial Director of Maker Media. He is the author or editor of over a dozen books on technology, DIY, and geek culture. He is currently a contributor to Boing Boing, Wink Books, and Wink Fun. His free weekly-ish maker tips newsletter can be found at garstipsandtools.com.

View more articles by Gareth Branwyn

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK