RSS
Johnathan writes "Now that volume 4 of MAKE is hitting newsstands, I have posted my article from volume 3: "DIY Security Bits". Figured it might be a good way to give blog readers more of a taste of the magazine content (though the existing sample PDFs are obviously the first stop for that.) The article details a method for making your own security bits for tamperproof screws, whose drivers are often ridiculously priced and just as ridiculously scarce." Link.
HOW TO make DIY security bits
Johnathan writes "Now that volume 4 of MAKE is hitting newsstands, I have posted my article from volume 3: "DIY Security Bits". Figured it might be a good way to give blog readers more of a taste of the magazine content (though the existing sample PDFs are obviously the first stop for that.) The article details a method for making your own security bits for tamperproof screws, whose drivers are often ridiculously priced and just as ridiculously scarce." Link.
Posted by Phillip Torrone |
Oct 25, 2005 07:13 AM
DIY Projects |
Permalink
| Comments (7)
| Email This |
| Digg this!
Recent Entries
- Virgil England's fantasy-land
- Novation Launchpad teardown
- Laptop Etch-a-Sketch via Arduino & Processing
- iPhone macro lens carousel
- New in the Maker Shed: OLLO kits
- BlueSMiRF found in credit card sniffer
- Mystery iPhone musical instrument - World's most expensive ocarina
- Stained glass d20s
- CRAFT Thanksgiving roundup
- 3D renderings of the Mandelbrot set
Comments
Oldest comments listed first.
Leave a comment
Subscribe to MAKE Magazine!
Subscribe today, save 42% and get web access to MAKE free. MAKE Digital Edition is available only to subscribers.
$34.95 / 1 year
(4 Quarterly Issues)
You can also use Fimo or Sculpey clay - the kind you bake - to make the impression of the screw head. Bake it, and spray it with Pam spray, then impress it again, and bake that part. Now you have a durable imprint of the screwhead and of the tool you need to make. More durable than spackling compound, at least.
Reply to this comment
Actually, if you just baked the first impression, wouldn't you have something capable of removing the screw?
ShapeLock might also work. It's a thermoplastic that melts in hot water and is solid at room temperature. Just melt some, blob it on the screw with something embedded in the blob for leverage. Then wait for it to solidify and rotate the screw. Might work.
Reply to this comment
The wonders of sculpey and especially shapelock were, in the case of the latter unknown to me at the time, and in the case of the former not immediately at hand, but you are of course both correct. On the other hand, spackle does the trick in a pinch, and I think of Make's DIY situation as being very much about doing tricks in pinches. :)
Reply to this comment
Seems like the simplest way would be to simply use your dremel to cut a flathead screwdriver slot into each screwhead. That is, you have so many screws that it would take less time to make a jig.
Reply to this comment
Can't always get to the screw head to mod it to fit your tools, but that's the simplest way for one or two screws. Recessed screws require the right driver bit, however.
Reply to this comment
This is a neat technique which is handy for really strange fasteners, however for the common security fasteners, a set of bits is definitely not "ridiculously priced" or "ridiculously scarce"
A basic 32 piece set, $14.95: http://xrl.us/h7dd
(I have this one, was on sale for $8. Haven't managed to break any of the bits yet.)
There are other sets available on that same site as well as other companies that specialize in electronics service/repair.
Reply to this comment
Overstock has the security bit set for $9.99. I've seen it for as little as $5.00.
On a completely different note, I like the little rubber holder that comes with the bit set. Has anybody seen just the holder for sale?
Reply to this comment