RSSLaser-etched Powerbook!
I didn't really plan using a $20,000 laser cutter on my 17" Powerbook to etch a 19th-century engraving of a tarsier, a nocturnal mammal related to the lemur (also a book cover image, from O'Reilly), but it seemed like it had to be done. The results are stunning - photos and more...
We visited MAKE pals Squid Labs in Emeryville, CA last night. They were recently profile in Wired as a " design firm that does differential equations, making solar panel driveways, swarming parachutes, a SourceForge for hardware and a comic book series for kid engineers." We'll post the video tour we did shortly, but here's one of the fun things we did: laser-cut a 19th-century engraving (book cover image, from O'Reilly) on to a 17" Powerbook. The results were stunning.
The O'Reilly books have these wonderful creatures on all the covers, and for a while, I thought they might make interesting tattoos and Second Life avatars, but since I don't plan on getting inked, a laser cutter looked like the next best thing.
Here's what the image looks like (low res).
Tarsier
The animal featured on the cover of Learning the vi Editor is a tarsier, a nocturnal mammal related to the lemur. Its generic name, Tarsius, is derived from the animal's very long ankle bone, the tarsus. The tarsier is a native of the East Indies jungles from Sumatra to the Philippines and Sulawesi, where it lives in the trees, leaping from branch to branch with extreme agility and speed. A small animal, the tarsier's body is only six inches long, followed by a ten-inch tufted tail. It is covered in soft, brown or grey silky fur, has a round face, and huge eyes. Its arms and legs are long and slender, as are its digits, which are tipped with rounded, fleshy pads to improve the tarsier's grip on trees. Tarsiers are active only at night, hiding during the day in tangles of vines or in the tops of tall trees. They subsist mainly on insects, and, though very curious animals, tend to be loners. Edie Freedman designed the cover of this book, using a 19th-century engraving from the Dover Pictorial Archive.
Saul from Squid Labs enters the dimensions of the PowerBook and imports the image. The laser cutter uses Corel Draw, which is kinda cute.
We filmed the process and will post a video soon; the laser is from Epilog.
Lining up the PowerBook.
It took about 10 minutes and it turned out great. The metal on the PowerBook reflects light in different ways; depending on the angle, the image looks solid or reversed out.
Etched Powerbook!
With the flash or lighting at an angle, the little guy looks like a snowy version and glows.
Posted by Phillip Torrone |
Nov 18, 2005 06:27 AM
Computers |
Permalink
| Comments (52)
Recent Entries
- HOW TO - build a water mortar
- Jake's steamcar project, dashboard redo
- Build your own water quality tester
- MAKE @ Yahoo! Buzz
- Made in Japan Vol. 3
- Super Breakout version allows for competitive or collaborative gaming
- How DIYers just might revive American innovation
- Light-Field camera makes blurry images a thing of the past
- Make a pizza box solar oven
- DIY Security system calls your phone
Comments
Oldest comments listed first.
That Is the Slickest thing I've ever seen for a power book!!!!!!
Very nice...Now the bigger question is how do I get mine done, I'm a DJ and I would love to get an Image of a turntable on my 15" powerbook!
Any information you could provide would be greateful!!
newkangol
The etching looks really nice and detailed. I have access to a laser etcher/cutter here at GA-Tech and if I get brave enough, I may do something similar to my PowerBook (or a number of other products I have around...) How rough is the etched AL surface? Is it not comfortable to touch or hold in the etched area now? I would also be curious to find out later on, how much dirt and grime collects in the etched areas and how easy it is to clean. Hope to hear a follow-up on these questions! Thanks.
here is a better picture (taken about one min ago)...
go to ETCHamac and get it done for about $150 for a 5"x5" image. I don't work for said company, just an observation...
Posted by: milombogo@gmail.com on November 18, 2005 at 9:21 PM
I'd like to see more details on how this was done.
According to the Epilog Laser FAQ you cannot etch metal, the laser bounces off. Unless you coat it and then it seems to weld the coating onto the metal, leaving black marks where the laser hits. Not what was done here.
Very cool - I've had some great experience with the Versalaser in getting weird things engraved with stuff, but a PowerBook is definitely pushing it there.
Though you're of course now obliged to do a full-size mural on the system cover of the HT : P
this looks great , i have done some work with a laser cutter (i have one in the shop i work in) and have dared to think about my 12" PB a few times.
Questions:
any concern over heat so close to your screen, did you disassemble any parts?
what depth did you go? how did it deal with the paint on the metal?good going!
Rivka
Great Idea. I have a bunch of scratches on mine and hadn't even considered doing this. We have a printer at school and my friends and I use it extensively, and always seem to forget about these types of applications. Did you have any problems with the laser reflecting back into itself? We were under the impression that metal was a no-no. What speed and power setting did you use?
Later
Hi.
What a wonderful example of the laser engraving technique! Modern technology alows to make this kind of art pieces in your everyday tools as your laptop. I write about this industrial technique at:
Just my 2 cents.
Frank
Hi.
What a wonderful example of the laser engraving technique! Modern technology alows to make this kind of art pieces in your everyday tools as your laptop. I write about this industrial technique at:
Just my 2 cents.
Frank
For those readers out there wondering where they could access such a Laser etcher, try looking around for trophy engravers that do either a) engraving on glasses (beer or wine) or b) black or clear acrylic trophies - these are typically done using lasers. If you have the design already done up in CorelDraw, and ask them nicely, they should be able to help.
I used to work in an engravers operating an older model 'Summit' machine from Epilog - very cool machine!! (http://www.trophy.co.nz/laser.htm - old workplace, showing photos of the old one at the bottom, and a new one which they've got since I was there which appears to be exactly the same model)
Wow that is awesome! I am amazed how cool that looks. You could start your own business doing that you know. Believe it or not the engraving market is fairly large with few competition these days. I bet you can make money for the most part, instantly, with your expertise and creativity.
Wow that is awesome! I am amazed how cool that looks. You could start your own business doing that you know. Believe it or not the engraving market is fairly large with few competition these days. I bet you can make money for the most part, instantly, with your expertise and creativity.
We can do it for you in the Portland Metro area .
Just be able to prove it is your notebook.( must be 18 for insurance reasons too)We have thousands of stock clip art images, or you can bring your own art and we will make your a one-of-a-kind!
What else you need etched?email for info
mobilelaserworks@yahoo.com
Posted by: mobilelaserworks on February 13, 2008 at 12:29 AM
Subscribe to MAKE Magazine!
Subscribe today, save 42% and get web access to MAKE free. MAKE Digital Edition is available only to subscribers.
$34.95 / 1 year
(4 Quarterly Issues)
Features and more @ MAKE!
MAKE @ The NYC Toy Fair 2008 - Covering DIY!HOW TO - Build the arms of assistance.
MADE in Japan - Part I.
MADE in Japan - Part II.
MADE in Japan - Part III.
Make store - Blinky bug kit - Blink!
Make store - Loud Objects Noise Toy Kit
Makers - MAKE Flickr pool contest. Win cool stuff!
Makers - Join the MAKE Facebook page - Meet other makers.
MAKE on Twitter - Tweet! Tweet!
What you're reading in MAKE - Data!
Add MAKE to your RSS reader - Real simple.
Why advertise on MAKE?
Read what folks are saying about us!
Click here to advertise on MAKE!
Phillip Torrone
Senior Editor
Tel: 707-827-7311
Gareth Branwyn
Robot Maker
Jonah Brucker-Cohen
Researcher
Natalie Zee Drieu
Senior Editor
CRAFT
Becky Stern
Culture jammer
Collin Cunningham
Sound Maker
Marc de Vinck
CNC Maker
Current Podcast
AHAB High Altitude Ballooning - Best of Weekend Projects
mp4|mov|hd|3gp|3g2|itunes This week on Best of Weekend Projects, we look back at part two of the AHAB (High Altitude Balloon Adventure). In this epic Bre & Co. travel to Eastern Washington to launch a GPS and camera enabled balloon...
More...
