RSS
I didn't really plan using a $20,000 laser cutter on my 17" Powerbook to etch a 19th-century engraving of a tarsier, a nocturnal mammal related to the lemur (also a book cover image, from O'Reilly), but it seemed like it had to be done. The results are stunning - photos and more...
We visited MAKE pals Squid Labs in Emeryville, CA last night. They were recently profile in Wired as a " design firm that does differential equations, making solar panel driveways, swarming parachutes, a SourceForge for hardware and a comic book series for kid engineers." We'll post the video tour we did shortly, but here's one of the fun things we did: laser-cut a 19th-century engraving (book cover image, from O'Reilly) on to a 17" Powerbook. The results were stunning.
The O'Reilly books have these wonderful creatures on all the covers, and for a while, I thought they might make interesting tattoos and Second Life avatars, but since I don't plan on getting inked, a laser cutter looked like the next best thing.
Here's what the image looks like (low res).
Tarsier
The animal featured on the cover of Learning the vi Editor is a tarsier, a nocturnal mammal related to the lemur. Its generic name, Tarsius, is derived from the animal's very long ankle bone, the tarsus. The tarsier is a native of the East Indies jungles from Sumatra to the Philippines and Sulawesi, where it lives in the trees, leaping from branch to branch with extreme agility and speed. A small animal, the tarsier's body is only six inches long, followed by a ten-inch tufted tail. It is covered in soft, brown or grey silky fur, has a round face, and huge eyes. Its arms and legs are long and slender, as are its digits, which are tipped with rounded, fleshy pads to improve the tarsier's grip on trees. Tarsiers are active only at night, hiding during the day in tangles of vines or in the tops of tall trees. They subsist mainly on insects, and, though very curious animals, tend to be loners. Edie Freedman designed the cover of this book, using a 19th-century engraving from the Dover Pictorial Archive.
Saul from Squid Labs enters the dimensions of the PowerBook and imports the image. The laser cutter uses Corel Draw, which is kinda cute.
We filmed the process and will post a video soon; the laser is from Epilog.
Lining up the PowerBook.
It took about 10 minutes and it turned out great. The metal on the PowerBook reflects light in different ways; depending on the angle, the image looks solid or reversed out.
Etched Powerbook!
With the flash or lighting at an angle, the little guy looks like a snowy version and glows.
That Is the Slickest thing I've ever seen for a power book!!!!!!
Very nice...
Now the bigger question is how do I get mine done, I'm a DJ and I would love to get an Image of a turntable on my 15" powerbook!
Any information you could provide would be greateful!!
newkangol
Reply to this comment
SquidLabs should consider getting a booth at MacWorld SF. I'm sure they'd be a hit (I'd bring in my PBs!) if the prices were reasonable.
Reply to this comment
The etching looks really nice and detailed. I have access to a laser etcher/cutter here at GA-Tech and if I get brave enough, I may do something similar to my PowerBook (or a number of other products I have around...) How rough is the etched AL surface? Is it not comfortable to touch or hold in the etched area now? I would also be curious to find out later on, how much dirt and grime collects in the etched areas and how easy it is to clean. Hope to hear a follow-up on these questions! Thanks.
Reply to this comment
effen gorgeous! I love it! Maybe O'Reilly should buy one to promote attendance at the various camps/shows/conferences.
Reply to this comment
bizarobot - the surface is not rough, you can barely tell it was etched. no far no dirt or anything, it's so nicely etched, it appears that it came like this.
Reply to this comment
Brilliant work!
What settings did you use on the laser cutter? I have access to one and would like to try this. Specifically, what depth are you cutting?
mcwresearch (at) gmail (dot) com
Reply to this comment
There's a company that can do something like this for you for a modest fee. I think it's called etchamac, they do iPods and Powerbooks. Not iBooks tho, so I feel left out.
Reply to this comment
here is a better picture (taken about one min ago)...
http://www.flickr.com/photos/pmtorrone/64558585/
Reply to this comment
awesome, is that your own laser cutter? and are there any places that'll do that sort of thing cheap?
nice work.
Reply to this comment
Wow! These guys could make a serious business out of that service. Just awesome!
Reply to this comment
very cool!
Reply to this comment
Freakin' beautiful!
Reply to this comment
Hey that's cool, but I think the critter's torso should have been centered so it's clucthing onto the apple. :)
Reply to this comment
amazing. that is just incredible. i want that now! ;)
Reply to this comment
I need to do this with my PB. Who can I contact to get it done?
Reply to this comment
go to ETCHamac and get it done for about $150 for a 5"x5" image. I don't work for said company, just an observation...
Reply to this comment
Wow... now that is too cool.
Reply to this comment
people will want this lots of people.
Reply to this comment
I LIKE IT! I LIKE IT! How can I get my 17 PB engraved? Or was this just a one-time-good-deal for you?
Reply to this comment
I'd like to see more details on how this was done.
According to the Epilog Laser FAQ you cannot etch metal, the laser bounces off. Unless you coat it and then it seems to weld the coating onto the metal, leaving black marks where the laser hits. Not what was done here.
Reply to this comment
Oh wow. I have to have that done on my PowerBook. Wow. What would the cost be for folks walking in off the street I wonder?
Reply to this comment
Oh wow. I have to have that done on my PowerBook. Wow. What would the cost be for folks walking in off the street I wonder?
Reply to this comment
Very cool - I've had some great experience with the Versalaser in getting weird things engraved with stuff, but a PowerBook is definitely pushing it there.
Though you're of course now obliged to do a full-size mural on the system cover of the HT : P
Reply to this comment
I can't believe that no one has asked yet: How much will it cost to get mine done with my own picture?
(Either that, or I can't believe I can figure out how to see the question and answers to this question :-)
Reply to this comment
Interesting, I wonder how I can put an image on the whole outside of my car...
Reply to this comment
I can't believe that no one has asked yet: How much will it cost to get mine done with my own picture?
(Either that, or I can't believe I can't figure out how to see the question and answers to this question :-)
Reply to this comment
Cost if I wanted to do this to my powerbook?
Reply to this comment
hmm, will it work on my plastic Dell?
Reply to this comment
That is very cool. And if someone steals your laptop, well... it may be very obvious.
Where else can we get stuff like this etched - ie: what kind of company are you working in, and where should we look.
Thanks for the article.
Reply to this comment
Great idea. Tatoo your stuff! Not your skin.
Reply to this comment
this looks great , i have done some work with a laser cutter (i have one in the shop i work in) and have dared to think about my 12" PB a few times.
Questions:
any concern over heat so close to your screen, did you disassemble any parts?
what depth did you go? how did it deal with the paint on the metal?
good going!
Rivka
Reply to this comment
Great Idea. I have a bunch of scratches on mine and hadn't even considered doing this. We have a printer at school and my friends and I use it extensively, and always seem to forget about these types of applications. Did you have any problems with the laser reflecting back into itself? We were under the impression that metal was a no-no. What speed and power setting did you use?
Later
Reply to this comment
HOLY SH**!! When can you do mine and how much will it cost???
James Blomquist
jblomquist@stny.rr.com
Reply to this comment
HOLY SH**!! When can you do mine and how much will it cost???
James Blomquist
jblomquist@stny.rr.com
Reply to this comment
hello i'm a "froggy" interested about laser engraving ...
I'm very impressed by your "little guy "
see the video soon ???
a bientot
Reply to this comment
hello i'm a "froggy" interested about laser engraving ...
I'm very impressed by your "little guy "
see the video soon ???
a bientot
Reply to this comment
hello i'm a "froggy" interested about laser engraving ...
I'm very impressed by your "little guy "
see the video soon ???
a bientot
Reply to this comment
FUCKING TIGHT!!!
i thought of that a long time ago.
Reply to this comment
FUCKING TIGHT!!!
i thought of that a long time ago.
Reply to this comment
http://flickr.com/photos/wls/68428237/
Reply to this comment
Amazing! If only I could get that done with Tux on my future PB.
Reply to this comment
bush baby
Reply to this comment
hey thats awesome! i'm a proud powerbook owner myself and would love to know what settings you used as far as power and speed on the laser cutter so that i can do the same on my laser cutter.
Reply to this comment
awesome! what were the settings you used for power and speed of the laser cutter (fematt@mit.edu)?
Reply to this comment
Hi.
What a wonderful example of the laser engraving technique! Modern technology alows to make this kind of art pieces in your everyday tools as your laptop. I write about this industrial technique at:
Laser engraving website
Just my 2 cents.
Frank
Reply to this comment
Hi.
What a wonderful example of the laser engraving technique! Modern technology alows to make this kind of art pieces in your everyday tools as your laptop. I write about this industrial technique at:
Laser engraving website
Just my 2 cents.
Frank
Reply to this comment
For those readers out there wondering where they could access such a Laser etcher, try looking around for trophy engravers that do either a) engraving on glasses (beer or wine) or b) black or clear acrylic trophies - these are typically done using lasers. If you have the design already done up in CorelDraw, and ask them nicely, they should be able to help.
I used to work in an engravers operating an older model 'Summit' machine from Epilog - very cool machine!! (http://www.trophy.co.nz/laser.htm - old workplace, showing photos of the old one at the bottom, and a new one which they've got since I was there which appears to be exactly the same model)
Reply to this comment
Wow that is awesome! I am amazed how cool that looks. You could start your own business doing that you know. Believe it or not the engraving market is fairly large with few competition these days. I bet you can make money for the most part, instantly, with your expertise and creativity.
Reply to this comment
Wow that is awesome! I am amazed how cool that looks. You could start your own business doing that you know. Believe it or not the engraving market is fairly large with few competition these days. I bet you can make money for the most part, instantly, with your expertise and creativity.
Reply to this comment
Phillip, I'd be very interested to see a homebuilt version of this!
Reply to this comment
Can you talk about how you prepared the artwork to get the right kind of results? (rmann AT latencyzero DOT com).
Thanks!
Reply to this comment
We can do it for you in the Portland Metro area .
Just be able to prove it is your notebook.( must be 18 for insurance reasons too)
We have thousands of stock clip art images, or you can bring your own art and we will make your a one-of-a-kind!
What else you need etched?
email for info
mobilelaserworks@yahoo.com
Reply to this comment