RSS
Raphael writes "This simple project shows you how to make a USB powered Nokia cell phone charger. The advantage is that it weighs much less than the bulky AC adaptor, and can be used wherever you have a computer or a laptop. I use this thing all the time now!" Link.
HOW TO - USB to Nokia Safe Charger
Raphael writes "This simple project shows you how to make a USB powered Nokia cell phone charger. The advantage is that it weighs much less than the bulky AC adaptor, and can be used wherever you have a computer or a laptop. I use this thing all the time now!" Link.
Posted by Phillip Torrone |
Dec 5, 2005 01:47 PM
Cellphones, DIY Projects, Electronics |
Permalink
| Comments (8)
| Email This |
| Digg this!
Recent Entries
- CRAFT Thanksgiving roundup
- 3D renderings of the Mandelbrot set
- New in the Maker Shed: Microbe Motel kit
- Science through graphic novels
- Tiny solar-powered brass engine in a wineglass
- Maker Shed kiosks at Fry's
- New hackerspace in Chicagoland: Workshop 88
- Mint tin electronics dev kit packs the essentials
- Olympus BioScapes competition winners
- Mac mailbox
Comments
Oldest comments listed first.
Leave a comment
Subscribe to MAKE Magazine!
Subscribe today, save 42% and get web access to MAKE free. MAKE Digital Edition is available only to subscribers.
$34.95 / 1 year
(4 Quarterly Issues)
Great stuff, works well on my old 8210 however my 6820 refuses to charge, gracelessly displaying "Not Charging" :/
Reply to this comment
Before I read this Makezine blog entry I tried to make one of these for a Nokia 6102b. It didn't work, I got the "Not Charging" message. I didn't look at the USB power signal on an oscilliscope, but it ap[eared to be rock solid on 5.12V.
This link's suggestion didn't make sense to me at all. All a diode would do is provide a ~0.5V drop of the voltage signal at the phone. I tried it anyway, with three little diodes in parallel (just in case one couldn't handle the 350 mA of the expected charge current). It wouldn't charge. I was getting 4.5V at the phone, which means the diodes were providing a voltage drop of ~0.6V.
I then hooked the USB cable up to a variable power supply and found that the phone would start charging when the power supply was at 5.2V, and would stop when it went down to about 5.09V. Given the 0.6V drop across the diodes this means that the phone happily charges at 4.6V (at 350mA!) but not 4.5V (2mA) -- much more sensitive than I expected, but not too suprising.
I pulled the diodes out and replaced them with a little 333uF dielectric capacitor pulled off of a fried video card, connected across the +5 and GND (red and black) wires of the USB cable, down near the phone side of the cable. Now the USB charging cable works great.
A capacitor across the power supply tends to reduce noise spikes on the power signal. When it comes to electrostatic filters they work well for mid and low-frequency spikes (kHz - Hz).
Reply to this comment
I own various phones, and their charging status on USB is as follows
Nokia N73 - Charges really well
W800i - Optimised charging (just like wall adapter)
W700i- Optimised charging (just like wall adapter)
W610i-Optimised charging (just like wall adapter)
Nokai 3230- Shows "Not charging"
On checking the voltages of wall adapters, The one on Nokia 3230 had 6v, while all others were less than 5.7V.
Probably thats why older phones like 3230 do not charge.
Reply to this comment
fyi, add a 2-5 ohm resistor in series (for current limiting) and *all* new nokia phones (with the mini charge plug) will charge straight from USB (5V)
Reply to this comment
Yes i have the same problem with a nokia 6120 with mini charge plug and it was fixed with the 5 ohm resistor in the 5 volts output.
(I use a regulator using a lm317 in order to trim the output voltage)
Reply to this comment
Yes i have the same problem with a nokia 6120 with mini charge plug and it was fixed with the 5 ohm resistor in the 5 volts output.
(I use a regulator using a lm317 in order to trim the output voltage)
Reply to this comment
Yes i have the same problem with a nokia 6120 with mini charge plug and it was fixed with the 5 ohm resistor in the 5 volts output.
(I use a regulator using a lm317 in order to trim the output voltage)
Reply to this comment
i tried with nokia 5200 it works but doesn't work with nokia 3230 phone. could you please help me to make a usb charger working for 3230 nokia?
Reply to this comment