RSS
Mike writes - "For those who don't know, Shapelock is a polymer (plastic) similar to polypropylene except that it has a very low temperature softening point. The idea is that you heat some water to around 160 degrees F and dump some of the pellets into the water to soften them to a moldable state. After molding, you then allow the plastic to cool and it once again takes-on its hard form. The label likens Shapelock to "modeling clay on steroids" and that's a pretty good analogy." - Link.
Plastic you can mold in your home for DIY projects
Posted by Phillip Torrone |
Mar 22, 2006 03:53 PM
Crafts, DIY Projects, Toolbox |
Permalink
| Comments (9)
| Email This |
| Digg this!
Recent Entries
- Building a folding table
- Maker Shed weekly wrap-up
- The Chumby has landed!
- Brainwave sofa by Unfold & Lucas Maassen
- Full MIDI drumset with Guitar Hero and Rock Band drums
- Hole punched art
- Portable induction accelerator
- Make: Halloween Contest 2009 - WINNERS!
- Telescope camera mod
- The patented 18 button OpenOffice mouse?
Comments
Oldest comments listed first.
Leave a comment
Subscribe to MAKE Magazine!
Subscribe today, save 42% and get web access to MAKE free. MAKE Digital Edition is available only to subscribers.
$34.95 / 1 year
(4 Quarterly Issues)
You can buy this stuff in the UK, from Maplins, under the name "Polymorph". A little expensive but worth its mass in gold for so many things. I've made otherwise expensive or impossible repairs in seconds with this stuff, as well as using it for all sorts of job related things.
Tough and hard plastic makes in minutes!
Reply to this comment
I tried the free sample from their site, and it's very cool! It melts at the very low temperature it says it does and is moldable by hand (meaning it won't burn your hand when you take it out the water) for a few minutes until it cools down. I'll start putting it to use when I think of some cool stuff for it...
Reply to this comment
I got some of this stuff last week and have been playing with it a lot, here are some things I've found out recently...
* With a pasta roller, you know, those silver machines you see at home goods stores, you can make nice even sheets for making good looking constructions. Making little planks also gives you 'stock' that heats up very quickly.
* Fusion brand rustoleum plastic spray paint sticks to it very nicely, so it can be painted, if you should need to.
* It has been advertised to be able to be machined, but since it behaves like nylon or delrin, that's not really true. It didn't like it when I tried. I haven't tried drilling or tapping it yet (hmmm, that sounds not quite right)
* With a hot putty knife you can connect new hot pieces to previously cooled constructions. I keep the putty knife in the same hot water pot where I'm heating the stuff. This gives you something to fish it out with.
* It's available in colors under the name 'friendly plastic'
* It's very cool stuff with a ton of uses. After you play with it for a while you start to see all kinds of things it could help with.
Reply to this comment
I wouldn't bother tapping it. Simply heat it up, then wrap it around a threaded rod or bolt, then later you can simply unthread it, leaving the threads behind.
Reply to this comment
I wish the folks at makezine would stop publishing stories using this stuff until the manufacturer is willing to send out an MSDS when requested, or does the decent thing and puts one on-line. This is flat out against the law. I would be careful if I where playing with this stuff, as far as getting it in my mouth, on my skin, or breathing any vapors from it, or any smoke from burning it.
Reply to this comment
hmm, you want -us- not post links to reviews?
Reply to this comment
Dear Sir or Madam:
I write to introduce myself as one of the best mold manufacturers ,from Dongguan, Guangdong, China, of plastic injection mold and die casting mold.
I enclose some pictures of new products for your reference, or visit my website: www.dymould.com and hope some of these items will be of interest
to you.
It will be my great pleasure to receive your inquiries for any of the items against which we will send you your competitive quotation. Hopes we can
cooperate in the future!
Looking forward to your favorable and prompt reply.
Best Regards
Yours: Willy
Dongguan Dongyun Mould Co., Ltd
Add:Changping Town,Dongguan City,Guangdong Province,China
Tel: +86-769-83502103 Fax: +86-769-83829376
Mobile: +86-13428428655
MSN: willy301201@hotmail.com
QQ: 284467183
E-mail: willy@dymould.com
Website: www.dymould.com
Reply to this comment
hi there, im new too all this and i was wondering if this is the stuff i would need to make hard plastic jewellery? does it come in different colours or anything? if anyone has any idea could they please reply to my email address caitlin_robb@hotmail.com as i might not find this site again! thanks! Xo
Reply to this comment
Does someone know how to mold a Buddha (like the one shown above) with this clear palstic, and may like to make a few dollars?? :)? Maybe about 6 inches (15cm) tall?
Reply to this comment