It’s fun to use mini solar cells to charge your gear or power small gadgets, and once you’ve learned the basics you can scale up to bigger panels. Let’s explore ways you can harness solar energy for your own DIY projects — mobile, wearable, or otherwise — and say goodbye to (some) batteries and plugging things in! 

Early Solar Energy

While the first solar electric panel is credited to Bell Labs in 1954, there have been a variety of other solar-powered devices for hundreds of years. The cell produced by Bell chemist Calvin Fuller and physicists Daryl Chapin and Gerald Pearson was the first silicon solar cell, following their success with semiconductors in 1947.

Figure A
Subscribe to Make: for this and more projects and articles.

Solar heat energy has also been used in a variety of ways, including architect Eleanor Raymond and MIT engineer Maria Telkes’s Dover Sun House in 1948 (Figure A). What looked like a wall of windows was actually a heat-collecting panel, with hot air transferred into “heat bins’” containing chemical salts which absorbed heat and stored it for later. The goal was to store enough energy to heat the building two to three days without sunlight. The processes Telkes developed are still used in molten-salt energy storage systems today.

Of course, solar energy goes way back to ancient civilizations using sunshine to dehydrate foods, using magnifying lenses to light fires, using reflection and positioning to tell the time or light a room, among other uses. When we think of it like that, contemporary solar cells are just a single point on a long continuum of solar possibilities! 

Photovoltaic Phenomena

Solar panels utilize what we call the photovoltaic effect — the ability of a material to emit electrons when exposed to light — to produce electricity.  This effect was observed as early as 1839 by French physicist Alexandre-Edmond Becquerel, who discovered that metal electrodes in an electrolyte solution produced a current when exposed to solar radiation. Although at the time he couldn’t explain it, it lay the foundation for what was to come. 

Figure B

Today many solar cells are made primarily of silicon (Figure B). Silicon is a semiconductor —
a material that partially conducts electricity, but also has some of the properties of insulating materials that don’t conduct. 

A Single Cell

A solar panel like you might see on someone’s roof is made up of many individual solar cells that are wired together. Each solar cell works by converting the sunlight hitting the semiconductor into electricity. The energy from the light (photons) is absorbed into the panel, which knocks electrons loose in the cell.

Each cell is designed with positively (p-type) and negatively (n-type) charged semiconductors in a sandwich, which creates an electric field that forces the drifting electrons to flow toward conductive metal plates on the outer layers of the cell, and then through wires like any other source of electricity (Figure C). This is the current, the strength of which determines how much electricity each cell can produce. The voltage of the cell is determined by the material, and solar cells also have an internal resistance to consider. Not 100% of the energy from the sun is converted to usable power by the cell; some light is reflected from the surface of the cell, or blocked by the metal lines on top of the solar cell that wire the cells together. Other factors like shade and sunlight intensity also affect the actual output of the panel, even if it has a particular rating. 

A Solar Panel

Much like other electrical circuits, individual solar cells can be wired in series or in parallel to modify the amount of voltage and current produced by the panel. Often, cells may be arranged in a combination of both to create the desired parameters. In a parallel circuit, current (amperage) increases and voltage remains the same. In a series circuit, voltage increases and current remains the same. In Figure D, you can see some mini solar cells arranged on a breadboard, wired in both configurations: series (top) and parallel (bottom). Each solar cell and panel will have a positive and negative wire.

Figure D

Many solar cells are often sealed into a single panel that has a wattage and voltage rating. Wattage is the power produced or used per second. For example, a 60-watt light bulb uses 60 joules of power per second. You can calculate the wattage of a circuit you want to power by multiplying volts by amps, for example in a 3 volt, 0.33 amp LED: 

W = V × A

W = 3 × 0.33

So this is a 1-watt LED.

Power over time is measured in watt-hours, which is watts × hours. To get an idea of how much power you might need to power your home for a whole day, you can check your power bill, which is often measured in kilowatt hours (kWh). The average household uses 20–30kWh a day; today I’m slightly embarrassed to admit I used 43 somehow.

Let’s say we got a new 250-watt panel. To determine the capacity of our setup, we will multiply panel watts × average hours of sunlight × 75% (as it is unlikely to be at full efficiency):

250 watts × 5 hours × 0.75 efficiency
= 937.5 daily watt-hours.


And then convert it to kWh like our electricity bill:

937.5 / 1000

= ~0.94kWh per solar panel.

Figure E, Reading the voltage on a 5V solar panel.

Your panel will usually tell you its voltage output, but that indicates the performance of the panel in ideal conditions. A great exercise is to take your panel outside, connect a multimeter to the panel’s positive and negative leads, and turn the meter to the voltage reading setting. As you
move the panel, you can clearly see how the voltage output is being affected (Figure E).
You can do the same thing to see the amperage output of a panel. 

Most solar panels have no amperage rating. Your circuit will draw current measured in amps (or milliamps, depending on the scale of your circuit). The consumption of amperage over time is measured in amp-hours (or milliamp hours). You’ll typically see this on batteries which have an Ah or mAh rating, so you may be familiar with the concept. Why is this important? Because most solar circuits, as we’ll see below, use a controller to charge the battery while the circuit draws power from the battery, instead of the panel directly powering the circuit. So you’ll want to calculate the draw of your circuit, and then find a battery that charges faster than your circuit discharges it.

Again, it’s important to remember that your solar panel output is charging your battery, and it’s your battery output that has to match your circuit requirements. For example, if my battery has 500 milliamp hours, and my LED draws 20 milliamps, my battery will last for 25 hours at full brightness:

Battery capacity (mAh) / Current draw (mA) 

500 / 20 = 25 hours

Don’t forget to make sure you’re always working in the same units, and convert if needed by moving the decimal point. 

Figure F, A 5V solar panel connected directly to a 5V DC motor using alligator clips.

You can connect a solar panel directly to the power and ground wire of any simple electronic component to power it with the right voltage (Figure F). But be carefuI: If the device has a processor or controller on it, the fluctuations in power might cause it to fail or to break. This is why we use tools to moderate the flow of electricity and ensure it doesn’t under- or overpower our electronics as the output of the panel changes. For example, while my panel might output 5V, my battery may only output 3.7V in a circuit with a controller. 

Solar Toolbox

After you’ve decided what exactly you want to power, you’ll need to find a solar panel. They come in all sizes, but I’m going to focus on simple electronics rather than powering your home, RV, or boat.

Figure G

Adafruit sells a wide variety of panels, from a tiny 5V 40mA badge, #700 (Figure G) to larger 6V panels in a variety of wattages and configurations. But my favorite is SparkFun #16835, a 10W 5V panel with a built-in USB port (Figure H). There are also some great flexible panel options if you want to make a wearable that is solar powered.

Figure H

In addition to the solar panel specs, it’s a good idea to keep an eye on the connectors it comes with: either barrel jack, JST, or USB, depending on your use. There’s nothing worse than getting all the parts for a project and winding up with the wrong connectors.

Figure I

If you’re looking for something smaller, I also love Osram’s tiny, 1/8″ BPW-34 through-hole solar cells (Solarbotics #SCPD, Figure I), 0.5V at 1.9mA, which isn’t enough to do much, but you can chain them together in any configuration. The Anysolar KXOB25-14X1F-TB offers 0.55V at 55mA, but in an even tinier surface mount package (Figure J); Digi-Key stocks it.

Figure J

After you’ve chosen a panel, you’ll want to pick a battery and a controller board. My favorite is the SparkFun Sunny Buddy solar charging board, #12885 (Figure K). You can connect a single LiPo cell or similar battery that meets your specs to the board, and the panel will charge the battery while the battery runs your circuit. Adafruit has a very similar DC solar charging circuit as well, #390.

Figure K

If your battery outputs 3.7V but you want to build something like a solar-powered Raspberry Pi which requires 5V, you may want to use one of Adafruit’s PowerBoost boards, #1903, to power your project (Figure L).  

Figure L

In this tutorial, I’ll show you how to connect a solar panel to your phone so that you never run out of power. There are lots of variations of this circuit, so make sure to verify your phone’s capabilities and ports, and your solar panel specs, before beginning.

Project Steps

Set Up the Charging Cable

First, cut the existing connector off the solar panel and place it on the back of the phone case to get the right position. Measure and cut the wire so that it can be plugged in, but doesn’t have much extra slack. Put the heat-shrink tube on, and solder the red and black wires to the USB connector. Heat the tubing so that the USB circuitry is covered.

Mount the Panel and Cable Holders

Glue the hinge to the edge of the solar panel and to the back of the phone case. Glue the rare earth magnet to the bottom of the solar panel so that it is held in place flat when it’s not being used.

Print the cable holder from the project page, or buy a suitable cable holder — and glue it next to the panel.

Chill and Charge!

Sit back, enjoy a drink, and charge your phone in the sun! Depending on the panel output, power consumption of your phone, and position in sunlight, you may get mixed results in the charge rate. Experiment!