Make: Projects – Harvesting chemicals from a battery

Science
Make: Projects – Harvesting chemicals from a battery
zincbatterycrosssection.jpg

This tutorial shows how to take apart a spent zinc-carbon dry cell of the common household type. Besides making for an interesting object lesson in electrochemistry, taking apart a spent D-cell, for instance, allows you to salvage many materials which can be of use to amateur chemists–materials which would otherwise probably end up in a landfill. Separated from their reactive components, the leftover parts of the battery can be safely added to most municipal recycling streams.

A zinc carbon cell (Wikipedia) contains manganese dioxide, which, among other things, is useful as a catalyst in the production of oxygen gas from hydrogen peroxide. It also contains metallic zinc, which can be used, for instance, as a reagent in the production of hydrogen gas from strong acid. Finally, it contains a carbon or graphite rod which can be used as an electrode in any of a number of electrochemical experiments, such as the electrolysis of water and the construction of an arc light or arc furnace.

Note that the battery in this tutorial is a zinc-carbon dry cell. This tutorial does not cover the dismantling of an alkaline-type cell. Alkaline cells are of slightly different internal construction and contain the strong base potassium hydroxide as an electrolyte, which is rather more dangerous to handle than the ammonium chloride/zinc chloride mixture used in zinc carbon cells. Zinc-carbon cells are commonly labelled “general purpose” or “heavy duty,” and will not have the word “alkaline” on the case.

Tools

  • Small flat blade screwdriver
  • Hobby knife
  • Scissors
  • Hammer
  • Mortar and pestle
  • Stainless steel or plastic strainer to fit coffee filter
  • Stainless steel or plastic tray to work in

Materials

  • Spent zinc-carbon or zinc-chloride D cell
  • Wax paper
  • Coffee filter

Step 0: Set up your work area

start.jpg

I recommend working in a tray with a layer of wax paper in the bottom. The tray will catch any stray manganese dioxide powder that gets loose during disassembly, and the wax paper will allow easy collection of the powder and its transfer to the mortar in step 7.


Step 1: Remove the outer case

pry casing at negative terminal.JPG

I find it’s easiest to start at the bottom (negative) terminal of the cell. Insert a small flat-bladed screwdriver under the rim of the casing where it’s crimped against the bottom gasket, right next to the seam that runs up the side of the cell, and pry up a small section of the rim.

pry casing at seam.jpg

Work the screwdriver down around the side of the cell, prying the casing open at the seam. Gloves are important during this step, not so much for protection against chemical exposure as for protection from the sharp exposed edge of the sheet metal casing.

remove casing with pliars.jpg

Once you’ve opened the seam, grab the exposed flap of metal with a pair of pliers and unwrap it from around the cell. Doing so will expose the zinc anode “can” beneath a plastic liner. It will also probably release the top gasket which insulates the case from the top terminal.


Step 2: Remove the plastic liner

cut wax wrapper.jpg

With a sharp knife, cut the plastic liner up the side of the cell as shown.

wax wrapper removed.jpg

Peel the plastic liner off from around the cell. This will probably release the steel bottom terminal and the bottom gasket.


Step 3: Expose the manganese dioxide powder

top terminal removed.jpg

The top metal terminal may lift right off, or it may require a bit of prying with a small flat-blade screwdriver.

plastic shield removed.jpg

Beneath the top steel terminal, there is a plastic shield with a carbon rod protruding. The carbon rod is sealed in place with a bit of asphalt. The plastic shield can be removed easily by prying with a flat-bladed screwdriver.

paper washer removed.jpg

Underneath the plastic shield is a paper washer. Use the blade of a hobby knife to spear it and lift it up and out of the cell, exposing the damp black powder of the manganese dioxide mixture inside.


Step 4: Cut off the zinc can

cutting off zinc can.jpg

In a spent cell, the zinc can will be thin and badly corroded, especially around the middle of the cell. Using a sharp pair of scissors, cut through the zinc can starting at the exposed rim and working down the side of the cell. I got all the way down one side before the top and bottom halves of the can just popped off.

zinc can removed.jpg

Step 5: Remove the paper liner

paper wrapper removed.jpg

Beneath the zinc anode is a paper wrapper around the black cathode powder. Use a hobby knife to peel off as much of it as you can. Remaining bits will be removed later, after the manganese dioxide is ground. All that should remain at this point is a carbon rod sticking out of a lump of manganese dioxide, probably with some bits of paper wrapper still stuck to its surface.


Step 6: Extract the carbon rod

carbon rod removed.jpg

Tap the lump gently with a hammer to break it up, and extract the carbon rod. Use the hobby knife blade to scrape off any manganese dioxide that remains on the carbon rod, and set the rod aside.


Step 7: Grind manganese dioxide

transferring mno2 to mortar.jpg

Transfer the chunks of damp manganese dioxide powder, and any remaining paper, into a mortar by lifting up, folding, and pouring from the wax paper work surface.

fine grinding mno2.jpg

Grind the chunks of manganese dioxide, in the mortar, with the pestle, using small, strong, circular motions. The powder should be damp when it comes out of the battery, but if it is not, moisten it with a bit of water. You want to avoid dry manganese dioxide dust in the air.

fine ground mn02 on filter.jpg

When powder is ground to about the consistency of coarse-ground coffee, transfer it from the mortar into a coffee filter. Using tweezers, pick out any remaining bits of the paper wrapper and add them to your paper recycling stream.


Step 8: Clean extracts

washing mn02.jpg

The manganese dioxide powder in this condition is ready to use in most amateur applications, including generation of oxygen gas from hydrogen peroxide. It is not pure, having residual carbon and electrolyte salt (ammonium chloride and/or zinc chloride) mixed in. The carbon is difficult to remove, but it is also, fortunately, largely inert. Residual salts can be removed by washing with hot water, as shown above, using a strainer. These salts can be safely disposed of down the sink, as can small amounts of manganese dioxide.

The zinc can is also, probably, not completely pure zinc metal, but for most amateur applications (including the generation of hydrogen gas by reaction with acid) can be used as such. It also may have residual salt on the inside surface, and this can be removed, again, by washing the pieces under hot water in a strainer.

The carbon rod will have residual manganese dioxide and possibly residual asphalt on its surface. To remove these, wet sand the rod lightly using medium-grit wet-or-dry sandpaper. This will also “activate” the surface of the rod, increasing its surface area and its utility as an electrode.


Notes and ideas

products.jpg

Save the manganese dioxide powder, the zinc pieces, and the carbon rod for use in other experiments. The steel casing and top and bottom terminals can be recycled with steel soup cans and other ferrous metal waste. The plastic liner, top gasket, and shield can be recycled with other common household plastics. The paper gasket, washer, and wrapper can likewise be added to normal paper recycling streams.

If you need purer chemicals, manganese dioxide, zinc metal, and ammonium chloride can be inexpensively purchased from The Maker Shed.

14 thoughts on “Make: Projects – Harvesting chemicals from a battery

  1. SKR says:

    I believe the Ammonium chloride is also used in the synthesis of a certain chemical beginning with the letter “e”.

    1. Sean Michael Ragan says:

      Maybe so, but there are much easier ways to come by a bit of ammonium chloride. It can be bought from many sources (we sell it in the Maker Shed, for instance) and it is easily prepared from common household chemicals.

  2. SKR says:

    It would be an awful lot of work for ammonium chloride.

  3. Anonymous says:

    The manganese dioxide can be used create a phosphate finish on non-stainless steel surfaces (parkerizing).

  4. Peter Sko says:

    Just one comment: No way “materials which would otherwise probably end up in a landfill”. I am sure all of you “Makers” are well into recycling and are also telling friends, family and neighbors about it !
    We all have to try to save our ressources and batteries are certainly a very valueable ressource…
    Peter

  5. AndyGondorf says:

    A nice hands-on educational suggestion, I like it a lot. But my old Dad used to say..”Never push a sharp edge towards any part of your own hand, it’s an accident about to happen”.

    I proved him right a few times as a kid with a penknife and lots of enthusiasm vs little listening.

    Try this experiment as shown in photos 2, 3 and 5 above and you might just find out the same thing.

    Lie the battery down and stab the tray with the screwdriver, not your own hand folks.

  6. parajumpers kodiak pas cher says:

    We have mastered several important matters through your post. I’d personally like to say that there is often a situation in which you will probably get a college loan and not have to have a co-signer such as a Federal government College student Help Loan. Still should you be getting this personal loan by using a regular financial institution then you definately need to be made ready to possess a co-signer willing to assist you. The lenders can bottom their own individual decision on a few parts nevertheless the most vital can be your credit history. There are several credit card companies that may moreover take a look at your projects history and determine depending on which but in almost all instances it will eventually depend on your record.
    [url=http://www.ulka.fr/Common/parajumpers/]parajumpers kodiak pas cher[/url]

  7. mackage parka femme says:

    Ssangyong- the business who’s wanting to develop a great deal ofnew modelsin introduced to obtain a greater piece with the business, partnered having ShanghaiAutomotive Companies Set and exhibited their particular newest stream-lined SUV, dubbed C200, in the ParisMotor Display a few days ago. The planning was done by Giugiaro due to the fact the ItalDesign design residence was in demand with all the appearance of the brand new versions being built.
    [url=http://www.multiprises.fr/images/moncler/]mackage parka femme[/url]

Comments are closed.

Discuss this article with the rest of the community on our Discord server!
Tagged

I am descended from 5,000 generations of tool-using primates. Also, I went to college and stuff. I am a long-time contributor to MAKE magazine and makezine.com. My work has also appeared in ReadyMade, c't – Magazin für Computertechnik, and The Wall Street Journal.

View more articles by Sean Michael Ragan

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK