Super Awesome Sylvia Shows How to Build the LOL Shield Kit

Arduino Technology
Super Awesome Sylvia Shows How to Build the LOL Shield Kit
YouTube player

Super Awesome Sylvia is back with an all new video about the LOL Shield! Take it away, Sylvia!

For this build, we’re laughing out loud at how many LEDs we’re going to solder in for the LOL (Lots of LEDs) Shield by our good buddy, Jimmie Rodgers! Let’s go!

For this blinky build, we’ll need:

  • The LOL Shield kit from the Maker Shed
  • Soldering iron and solder
  • An Arduino
  • A Computer
  • A USB Cable
  • Wire snips
  • And last but not least, a vice or helper hands (not required, but really useful!)

First, get yourself a nice clear workspace and carefully dump out the contents of the kit. There’s a lot of LEDs in there! I mean a LOT! Take all your parts and lay them out. You should have one PCB, 133 itty bitty LEDs, and one 36 pin header strip. The LEDs are first, so get that soldering iron hot!

Remember, LEDs have polarity, they need to be put in correctly. The short leg is the negative (or cathode) and the long leg is the positive (or anode). From the top we can also see the side with the negative lead is flat, matching up with the silkscreen on the PCB. Make sure your LEDs match up with the silkscreen and they should be right every time.

Carefully place your LEDs to fill one column of nine, pinch the leads a bit (so they don’t fall out!), then flip the board over. Now carefully solder in only one lead of each LED. Once you’ve got the column soldered, flip it back over. Oh my gosh! They’re like crooked teeth!! Not to worry though…

Just heat up the soldered joint for an LED, while pressing and wiggling the top down flush with the board. Tada! Perfectly straight up and down. Repeat with the rest, then solder the other leads, trimming as you go. Only 13 more columns left to do! Be sure and check out the complete instructions by Jimmie (and some of his other cool kits and projects).

Whew! Once all your LEDs are in place, put the headers into your Arduino and snip them off to the right length. When done, place the shield over until it fits, then solder up the headers. Aaand… you’re done! Wahoo! Now head over to your computer, plug in the Arduino, get the LOL Shield library into your Arduino IDE (following the instructions at Jimmie’s site), and upload the test pattern example sketch. If everything went well, you should see the test pattern. If any LEDs fail to light (which happened to us!) check for cold solder joints, wiggle the offending LED, or if worse comes to worse, desolder it and put in a new one. The PCB traces are small and delicate so it’s best to avoid this if you can.

So, what can you do with your awesome Lots of LEDs? How about a scrolling marquee for your very own message, Conway’s Game of Life (a cellular automaton simulation), a custom animation (try and make your own at the LOL Shield Theater), a video or animated gif? If you add a button and a potentiometer, you can play tetris, space invaders, pong or even make your own game! You’re only limited by your imagination, coding skill, and how much you can squeeze on this little chip.

When you’re done, try and experiment with different programs or games, maybe try and write your own or add a speaker for sound effects, respect your soldering iron, and get out there and MAKE something!

Subscribe to the MAKE Podcast in iTunes, download the m4v video directly, or watch it on YouTube and Vimeo.

6 thoughts on “Super Awesome Sylvia Shows How to Build the LOL Shield Kit

  1. Lambry Danchev says:

    Super !

  2. AMalePoet says:

    That tears it if she can solder I have to get in more practice. 

    1. Matt Richardson says:

      There’s no better way to practice soldering than with the LOL Shield!

  3. Stephen Griswold says:

    One suggestion, as I’m more than sure Colin Cunningham will also agree, one way to make sure the LED’s (and other components) not fall out, or mis-allign, is to bend one (or both) leads outward, not pinch inward as suggested in the video. this way, the device will pull against the board. Pinching them inward, allows them to roll, as the lead pulls back through the through-holes. I was taught this when I soldered my 1st project. (a florescent digital clock from Heathkit.) (which I also made my 1st hack.. cut the trace to the colon, and added a wire from the clipped dot lead, to the flashing colon side of the alarm switch, to indicate seconds.)

  4. Naveen Navigator says:

    can anybody give me the layout of that LoL Shield v1.5 PCB? i know i can buy directly over the internet. but i need its true layout

  5. Lysa Bacon says:

    Great videos Sylvia! Got the potentiometer figured out, now about that button… Unable to figure out how to wire the button for tetris or invaders. Thanks in advance for any help.

Comments are closed.

Discuss this article with the rest of the community on our Discord server!
Tagged

Matt Richardson is a San Francisco-based creative technologist and Contributing Editor at MAKE. He’s the co-author of Getting Started with Raspberry Pi and the author of Getting Started with BeagleBone.

View more articles by Matt Richardson

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK