Hot Topics:
See All Topics

Make: Projects

Headboard Made with 2 Doors

A modern, sleek wood headboard with accent lighting which is easy to make from two hollow-core wood doors.

  • By smith library
  • Category: Furniture
  • Time Required: 4-5 days (it rained so I let the stain and polyurethane dry extra long)
  • Difficulty: Easy
Headboard Made with 2 Doors

This project will walk you through every step of making a modern, sleek wooden headboard with accent lighting from two hollow-core wood doors.

(Two parts of this project require an assistant or one very coordinated and strong person.)

Time: 4-5 days (it rained so I let the stain and polyurethane dry extra long)

Cost: under $200 (before tax)

  • Paint Brushes
  • Screw drivers

Steps

Step #1:

NextHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 Doors
  • I built this headboard for a queen-size mattress which was only on a plain metal frame. The width is 60". I felt the headboard would look visually balanced with about 2" wider on each side. So the doors I bought were 32" wide for a headboard width of 64". This left enough space for the bedside tables to be close to the bed without bumping up against the headboard.

Step #2:

NextHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 Doors
  • I followed the suggestions on the can and used a Pre-Stain Conditioner.
  • The Pre-Stain Conditioner looks milky when applied but dries clear.

Step #3:

NextHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 Doors
  • I used Ebony colored stain, applied the stain, waited 15 minutes and wiped off all the excess stain and buffed the doors with soft cloths until no extra stain lifted off. After 12 hours I applied a second coat of stain, waited 15 minutes and wiped off all the excess stain and buffed the doors with soft cloths until no extra stain lifted off.

Step #4:

NextHeadboard Made with 2 Doors
  • I stained both sides of both doors. Since I was using a dark stain the grain became very visible and so did any flaws in the doors. Staining both sides gives you the opportunity to pick the best side to be shown.
  • I also stained the edges since they will be exposed. Take care to wipe off any stain that drips to the underside.
  • Tip: Use cloths that are lint-free. Old sheets worked best. I used a lot (I mean a lot!) of cloths because I put on a nice coat of stain like I was painting and after 15 minutes wiped most of it off.
  • I waited a full 12 hours before doing the next step.

Step #5:

NextHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 Doors
  • Seal the doors with polyurethane. Since I had stained both sides of the doors I also sealed both sides and all the edges to keep the stain from rubbing off onto the flooring, bedding and walls.
  • I allowed the doors to completely dry for 24 hours before the next step.

Step #6:

NextHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 Doors
  • After the polyurethane was completely dry I moved the doors to the bedroom before connecting them to each other. The brackets will not make the doors one solid piece and can be easily bent but once the headboard is in place it will be stable.
  • Attach four tie plates (which were located in the lumber/decking department of my hardware store) with small wood screws which fit the tie plates. The tie plates I used were about 5” long and almost 2” wide. There are 5 columns of holes. I screwed through the second and fourth columns, using the middle row to center the plates.

Step #7:

NextHeadboard Made with 2 Doors
  • You can usually see the width of the solid wood edge of the door on the top/bottom edges. Here you can determine the placement of the tie plates. The holes in the second and fourth column of the tie plates I used fell exactly in the center of the solid wood edges of the doors. Here I sought the assistance of my husband; he attached the tie plates while I pushed the doors together tightly and kept them straight and the tops even with each other.

Step #8:

NextHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 Doors
  • I used heavy duty D-ring / triangle strap hangers to attach the picture wire. The hangers were screwed in 5” from the top on the outer edges of the now-bracketed doors and the wire was attached with enough give to be exactly 2” from the top of the door. Usually pictures are wired at 1/3 the length of the frame but I felt this was too much for the doors. And 5” worked very well.
  • Follow this link to see instructions for knotting picture wire.

Step #9:

NextHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 Doors
  • I attached Ikea LED light strips to both sides of the back of the headboard. The Ikea lights are meant to be attached flat but the light would have reflected straight back against the wall. I wanted the light to reflect out the sides so used the adhesive strips that came with the lights to attach them on their sides facing out. I attached them about 6” from the top of the headboard and about 1-1/2" in from the sides.

Step #10:

NextHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 Doors
  • Stand the completed headboard up. This will require 2 people because the headboard is so wide and the brackets merely hold the 2 doors together for a visual effect and do not lend any structural integrity at all to the headboard. Attach to the wall like a picture. I used a heavy-duty 50-lb MonkeyHook®. The instructions on the hook I used said to subtract 1/4” from the measurement. So I stood up the doors, marked the center and inserted the MonkeyHook 1-3/4” down.
  • The doors are actually standing on the floor so the hook isn’t holding any weight but acting like an anchor to keep the headboard from tipping forward.
  • Tip: I used a wire hanger to grab the picture wire and hold it while my husband lifted the one side of the headboard enough so I could hook the wire onto the hook.

Step #11:

Headboard Made with 2 DoorsHeadboard Made with 2 DoorsHeadboard Made with 2 Doors
  • Move the bed frame and bed into place in front of the headboard. Plug in the LED lights. Done!
  • The last picture is at night with all the room lights off and only the LED lights on. Great ambient light!

Conclusion

Total cost before tax was about $160.

Related Projects

Plywood Coffee Table
Plywood Coffee Table

By: Andy Lee

Install a Penny Countertop
Install a Penny Countertop

By: Shane Selman

Geared Candleholder
Geared Candleholder

By: Benjamin Cowden

Custom Computer Desk
Custom Computer Desk

By: Randy Kangas

Hollow-Core Door Table
Hollow-Core Door Table

By: Sean Michael Ragan

Ant Farm Room Divider
Ant Farm Room Divider

By: Matt Maranian

Magnetic Knife Rack
Magnetic Knife Rack

By: Adam Mann

Outlet-Mount Device Charging Pocket
Outlet-Mount Device Charging Pocket

By: Sean Michael Ragan

In the Maker Shed

Makey Makey Standard Kit

Makey Makey Standard Kit

BrushBots

BrushBots

Brooklyn Aerodrome Flying Wing Kit

Brooklyn Aerodrome Flying Wing Kit

Brooklyn Aerodrome Flying Wing Kit

MAKE Rovera 4WD Arduino Robot Kit

Leave a Reply

Fill in your details below or click an icon to log in:

Gravatar
WordPress.com Logo

You are commenting using your WordPress.com account. ( Log Out / Change )

Twitter picture

You are commenting using your Twitter account. ( Log Out / Change )

Facebook photo

You are commenting using your Facebook account. ( Log Out / Change )

Cancel

Connecting to %s

Join the MAKE Forum
Makershedad_DOTW_%20Makershields

// What's Trending

Raspberry Pi Design Contest
Raspberry Pi Design Contest
  • By: Nick Normal
  • Hits: 25312
Ten Tips for Adhesive Tape
Ten Tips for Adhesive Tape
  • By: Michael Colombo
  • Hits: 10096
Lost PLA Casting from 3D Prints
Lost PLA Casting from 3D Prints
  • By: Eric Weinhoffer
  • Hits: 7389
Seventeen Sneaky Secret Hides
Seventeen Sneaky Secret Hides
  • By: Sean Michael Ragan
  • Hits: 4723
I Have a (Puzzling) Dream
I Have a (Puzzling) Dream
  • By: Gareth Branwyn
  • Hits: 3669
10 Things to Connect to Your Raspberry Pi
10 Things to Connect to Your Raspberry Pi
  • By: Alasdair Allan
  • Hits: 2761
47 Raspberry Pi Projects to Inspire Your Next Build
47 Raspberry Pi Projects to Inspire Your Next Build
  • By: Nick Normal
  • Hits: 1526
Teardrop Camper Trailer
Teardrop Camper Trailer
  • By: Werner
  • Hits: 1367

// What's Shared

A better way to slice a pumpkin
A better way to slice a pumpkin
  • By: Sean Michael Ragan
  • Shares: 42287
DIY Nerf Darts
DIY Nerf Darts
  • By: Adam Flaherty
  • Shares: 27067
100 Dollar Store Organization Ideas for Craft Rooms and Beyond
100 Dollar Store Organization Ideas for Craft Rooms and Beyond
  • By: Haley Pierson-Cox
  • Shares: 22736
In the Maker Shed: Minty Boost USB Charger
In the Maker Shed: Minty Boost USB Charger
  • By: Maker Shed
  • Shares: 22042
Mad’s Mouse House
Mad’s Mouse House
  • By: Meg Allan Cole
  • Shares: 13844
Lace Princess Crowns
Lace Princess Crowns
  • By: Meg Allan Cole
  • Shares: 13096
I Have a (Puzzling) Dream
I Have a (Puzzling) Dream
  • By: Gareth Branwyn
  • Shares: 10501
Play the Rings of a Tree Trunk Like a Record
Play the Rings of a Tree Trunk Like a Record
  • By: Matt Richardson
  • Shares: 10251

// Most Commented

Jason Poel Smith Picture
DIY Hacks & How To’s: Get Emergency Power from a Phone Line
  • By: Jason Poel Smith
  • Comments: 39
sample parts
Resin Casting: Going from CAD to Engineering-Grade Plastic Parts
  • By: Michal Zalewski
  • Comments: 35
Don't get me wrong, they're cheap and often get the job done, but they were made to not drive well. They were designed specifically in the early 20th century to cam out when too much force was applied. Now that we have torque-limiting drills this isn't a problem anymore, yet somehow we still use them.
Ten Tips for Screws and Screwdrivers
  • By: Michael Colombo
  • Comments: 27
We use the phrase "two by four" in common parlance, but did you know it's actually 3.5 inches wide? Don't make assumptions on size; always measure first.
Ten Tips for Better Measurement
  • By: Michael Colombo
  • Comments: 19
BrainMachineWorkshop
Is it a Hackerspace, Makerspace, TechShop, or FabLab?
  • By: Gui Cavalcanti
  • Comments: 15
E59A0674
Makers on TV: Big Brain Theory
  • By: Sabrina Merlo
  • Comments: 12
Arduino Yun
Arduino Announces New Wireless Linux Board
  • By: Andrew Terranova
  • Comments: 12
IMG_4400
Tool Review: BioLite CampStove
  • By: Keith Hammond
  • Comments: 10
MAKE
Trending Topics
About Maker Media

Make on Twitter Make on YouTube Make on Pintrest Make on Flickr Make on Facebook Stumble Make Magazine MAKE on Instagram MAKE on Google+

%d bloggers like this: