Hot Topics:
See All Topics

Make: Projects

Sous Vide Immersion Cooker

Build your own immersion cooker for around $75.

Sous Vide Immersion Cooker

I’m fascinated by sous vide cooking, in which foods vacuum-sealed in plastic are immersed in a precisely temperature controlled hot water bath to achieve optimal doneness.

But most sous vide (soo-veed) cooking machines are commercial models that cost north of $2,000, and the first “home” version, the countertop SousVide Supreme, is priced in the neighborhood of $450 (not including vacuum sealer), which is still a steep investment for something that essentially keeps water warm. I decided to build a better device on the cheap. Behold, the $75 DIY Sous Vide Heating Immersion Circulator! By scrapping together parts from eBay and Amazon, I created a portable device that heats and circulates water while maintaining a temperature accurate within 0.1°C. And unlike the SousVide Supreme, it mounts easily onto larger containers, up to about 15 gallons, for greater cooking capacity. The water is heated by three small immersion heaters and circulated by an aquarium pump to keep the temperature uniform. An industrial process temperature module controls the heaters, and an eye bolt lets you clamp the entire apparatus to the rim of a plastic tub or other container. To cook sous vide, you also need a vacuum sealer, which this project does not include. I bought a good one new for about $112.

This project first appeared in MAKE magazine, Volume 25. Subscribe today!

  • Bowl of cold water
  • CNC laser cutter (optional)
  • Drill and drill bits 1 8" 5 32"
  • Hobby knife
  • Marker
  • Multimeter
  • Phillips screwdriver
  • Rotary cutting tool with router bit
  • Soldering iron and solder
  • Stove and oven mitt
  • Wire cutters and strippers

Steps

Step #1: Cut the acrylic enclosure.

NextSous Vide Immersion Cooker
  • This is the most difficult part of the project. For your cooker to be sturdy, water-resistant, and decent looking, the mounting holes must be cut precisely. I used a CNC laser cutter I have access to at work, but with a steady hand you can achieve the same results using a rotary tool like a Dremel.
  • Download and print the cutting template from Files (after Introduction). This template matches the heaters, controller, and switches I used, so you’ll need to adjust the shapes and sizes if you use different parts.
  • Following the template, cut out the 3 holes for the immersion heaters on one side of the acrylic container, near its base.

Step #2:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Mark and cut the small oval-shaped hole for the water pump power cord and a circular hole for the thermocouple
  • Follow page 2 of the template to mark and cut openings in the lid of the container for the controller, switch, and power cord.

Step #3:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Cut the power cord off each heater, leaving an 8" tail of wires from each coil end.
  • Using your hobby knife, scrape the flat sides of the heater handles to remove the lettering and flatten the circular rim where it meets the cord.

Step #4:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Fit all 3 heaters into their holes in the container, such that the coils stick out and line up. Your finger should be able to fit through all 3 coils at once. Trim the holes if needed to make the heater handles fit snugly.
  • Caulk a fully waterproof seal around the heater handles on the outside of the enclosure and let dry overnight. For added strength, add hot glue over the caulk after it’s dried. The hot glue only needs 5 minutes to dry before continuing.

Step #5: Attach the mounting bracket.

NextSous Vide Immersion Cooker
  • Cut a 7"×2" rectangle out of ¼" acrylic. The cut sides don’t have to be perfect as long as the rectangle dimensions are approximate. Use a rotary cutter to rout a shallow recess that’s the same shape and size as the nut for your eye bolt, centered at one end, as shown on page 3 of the template. Drill a ¼" hole through the center of the recess for the eye bolt to pass through.

Step #6:

NextSous Vide Immersion Cooker
  • It’s time to bend the acrylic sheet. Clear a countertop near your stove, put a bowl of cold water within reach, and mark the bend point lines from the template onto the acrylic.
  • If your countertop is too thick or thin for this process, you’ll need to bend the sheet around a hard, stable object, approximately 2" thick, such as a 2×4.
  • Turn one of the front burners on high, hold the undrilled end of the acrylic with an oven mitt, and place the drilled end with bend lines a few inches above the burner, moving the acrylic around and turning it to heat both sides. If it begins to form small bubbles, move it away from the heat a little. When the acrylic starts to curl away from the heat, it’s ready to bend.

Step #7:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • With the recess for the nut facing outward, bend the acrylic around the edge of the counter (or other object) approximately along the marked lines to form a “J.” While in place, press the middle segment of the J against the edge of the countertop to make it flat. Immediately drop the acrylic into cool water so that it holds its form.
  • Position the middle segment of the J bracket against the heater side of the enclosure, with the bracket’s nut side aligned along the enclosure’s rim. This is how you’ll bolt these 2 pieces together. Mark and drill two 1" holes through the bracket and 2 matching holes in the enclosure. Check that the 4-40 machine screws fit through both pairs of holes.

Step #8:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Liberally apply super glue to the underside of the bracket, and bolt it to the enclosure with the machine screws and nuts.
  • Liberally apply more super glue to the recessed area for the eye bolt nut, and set the nut in place. Reinforce the bond with hot glue, but don’t obstruct the hole in the nut.
  • For more support, you can cut a 1½" acrylic round with a hole fitting the nut, and glue it to the J-clamp overlapping the opening. This will provide extra gluing surface and take stress off the nut.

Step #9: Attach the pump.

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Cut the water pump’s power cord about 8" from the pump. Reserve the severed cord, which will become the cooker’s power cord.
  • Position the pump on the long side of the bracket, with its cord pointing toward the enclosure and its top aligned with the top of the heater coils. The pump should be placed so its outlet is more or less pointing through the coils. Mark the locations of the suction cup feet on the bracket.

Step #10:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Drill two 5/32" holes through the bracket at the exact centers of the suction cup locations. Check that the holes can accommodate the sheet metal screws, and enlarge them if needed by wiggling the drill bit.
  • Remove the suction cups from the pump, and attach the pump to the bracket with the sheet metal screws in the suction cup holes.

Step #11: Complete the wiring and assembly.

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • For the big picture, refer to this wiring diagram.
  • Don’t ever power on the heater coils unless they are submerged in water! (They’ll burn out.) And if you’re unfamiliar working with AC power, seek assistance from someone who’s knowledgable.
  • Split the heater cords apart and strip about 2" of shielding away from each end. Twist and solder together 1 lead from each of the heaters, then repeat for the other set of leads to wire the 3 coils in parallel.
  • Cut two 18" 14-gauge wires and strip 2" of shielding from each end. Use wire nuts to bundle one end of each wire with a set of heater leads. One wire will connect to AC power, and the other will connect to the relay.

Step #12:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Remove the mounting ring from the PID controller, fit its front panel out of the opening you cut for it in the acrylic lid, and secure the controller from the back by replacing the mounting ring.
  • Fit the power switch into its hole in the acrylic lid and secure it with its included mounting nut. Run the power cord you cut from the water pump through its hole nearby. Separate its leads, strip ¼" of shielding, and solder 1 lead to 1 leg of the power switch.
  • Cut and strip 3 short (about 4") lengths of 14-gauge wire. Twist-bundle 1 wire with the free power cord lead, 1 lead from the water pump, and 1 of the 14-gauge leads from the heaters. Secure the bundle with a wire nut, and screw the short wire to terminal #1 on the controller.

Step #13:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Solder the other 4" piece of 14-gauge wire to the unconnected leg of the power switch, and then screw the other end to the #2 terminal on the controller’s.
  • Make a new bundle connecting the free lead from the water pump, the wire from the #2 terminal, and the third short length of 14-gauge wire.
  • Orient the relay so that its underside (with the pins) faces you, and the row with 3 pins is facing down. Solder the free lead from the previous step to the upper left pin of the relay.

Step #14:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Solder the free lead from the heater bundle to the middle bottom pin of the relay.
  • Cut and strip two 6" lengths of 22-gauge wire. Solder one to the bottom right pin of the relay and connect it to the #5 terminal on the controller. Solder the other piece to the relay’s bottom left pin and connect it to the #6 terminal.
  • Insulate and strengthen the relay connections with a liberal application of hot glue. Wrap the relay and wires with electrical tape.
  • Apply hot glue around the holes for the power cord and water pump cord, to prevent steam or water from leaking into the enclosure.

Step #15:

NextSous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Insert the PT100 thermocouple into its hole in the enclosure and secure with hot glue. Connect its red lead to the controller’s #10 pin, its blue lead to the #11 pin, and the yellow lead to the #12 pin.
  • Put the acrylic lid on the open end of the container, and apply a neat strip of electrical tape around the edges to hold it on. (Once you’ve verified that the cooker works, you can then glue the seam.) Insert the eye bolt through the nut.
  • Everything is wired up and assembled. Now you probably want to see if it works. BUT WAIT! Don’t turn the machine on (ever!) unless the coils are submerged in water or else they’ll burn out in about 5 seconds. I learned this the hard way.

Step #16:

NextSous Vide Immersion Cooker
  • Fill a container with enough water to cover the top of the circular part of the heater coils by ¼"–½". Mount the cooker inside with its bracket hanging over the lip, and tighten the eye bolt to secure.
  • Plug in the cord and flip on the power switch. If the PID controller turns on and the pump starts pumping, that’s a good sign. Note that the heaters may not warm up yet, depending on what the controller’s default target temperature is.
  • 120V AC current is dangerous and misuse can injure or kill. Seek the assistance of a qualified electrician if needed. Take care to keep the control box and wires out of the water or other liquids. And once you’ve tested your cooker, seal the lid on the control box.

Step #17: Program the controller and test.

NextSous Vide Immersion Cooker
  • For the model CD101 PID controller manual and a full sequence of photos showing how to program it for this project, visit http://www.makezine.com/25/sousvide.
  • The PID controller defaults to a different thermocouple than the PT100 used here, so you need to reconfigure it for a PT100 sensor. Press and hold the SET button until AL1 appears, then keep pressing SET until you see LCK (lock) with 1000 underneath. To unlock the settings, we need to change this value.
  • Use the left-arrow key to move the cursor and the up-arrow key to change LCK to 1100. Then press SET again to exit the menu.

Step #18:

NextSous Vide Immersion Cooker
  • Push and hold the SET and left-arrow keys together until you see COD (code). Use the arrow keys as before to set this value to 0000, then press SET again to see SL1, the sensor type symbol.
  • Change SL1 to 1100, for the PT100 sensor. Press and hold the SET and left-arrow keys again to exit. Then re-lock the settings by setting the value of LCK back to 1000, as in Steps 6a–6b.
  • It’s time to heat things up. The top line of the display (green) shows the current temperature, and the second line (orange) shows the target. Set a target temp by tapping the SET button, using the up and down arrows to specify the target, and pressing SET again to confirm. 50°C is good for testing.
  • If all’s well, the OUT1 light will turn on and you’ll hear a soft clicking as the relay turns on the heaters. The temperature reading will increase, and you’ll hear more frequent clicking as it approaches the target.

Step #19: Use It

NextSous Vide Immersion Cooker
  • A good vacuum seal is essential to sous vide. Without air pockets, the heat transfers into the food evenly and efficiently. A good seal also dramatically decreases the risk of bacterial contamination from long incubation at low temperatures.
  • I use a FoodSaver V3835, which I bought for just over $100 with a 20% coupon at Bed Bath & Beyond. It uses rolls of plastic, so you can make the bags any size you need. I recommend against using cheaper handheld sealers. I’ve tried a few and had problems creating a reliable seal.
  • With any sealer, always wipe clean and dry the end you’re going to seal, or the plastic layers might not melt together properly.
  • Using a zip-lock bag instead of a vacuum sealer is actually OK for cooking times up to 4 hours, but also riskier for leaking and contamination.

Step #20: Kitchen Tests

NextSous Vide Immersion Cooker
  • To reveal the power of sous vide, cook an egg in the shell (no plastic needed) at 64.5°C for 1 hour. This yields an amazing transformation: perfectly soft whites, not runny or rubbery, and a yolk with the consistency of a rich pudding. It’s impossible to achieve this through any other cooking method, and it’s spectacular the first time you experience it.
  • I expanded on this amazing transformation by breading the yolks and quickly deep-frying them to add a crunchy shell. See my recipe at http://www.makezine.com/25/sousvide.
  • Next, try cooking a good, thick steak. Unlike conventional cooking methods, sous vide gives you a perfect medium-rare steak all the way through. To finish the steak, pat all sides dry and sear like crazy with a propane torch (the kind plumbers use).
  • Some things that don’t work well sous vide, in my experience, are broccoli, kiwi, and strong aromatics. Note also that if you sous vide with too much garlic, your whole house will smell like feet.

Step #21: General-Purpose Temp Controller Mod

Sous Vide Immersion CookerSous Vide Immersion CookerSous Vide Immersion Cooker
  • Several people have modified this project so that the relay switches a power outlet that the heaters and pump plug into, and the probe plugs into an added jack. Then, if a heater burns out, you plug in another one rather than having to mess with glue and solder. Modularizing the control and power components this way also lets the machine double as a precise temperature controller for a smoker box, such as Alton Brown’s DIY flower-pot smoker (see http://www.makezine.com/25/sousvide). You just plug in the hotplate filled with wood chips.
  • Pick up a few steaks and break out your blow torch — it’s time to start cooking like a geek!
  • For hole templates, the CD101 PID controller programming instructions and manual, Scott’s Deep-Fried Sous Vide Egg Yolks recipe, and other resources, visit http://www.makezine.com/25/sousvide.

In the Maker Shed

Calculator Kit from Spikenzie Labs

Calculator Kit from Spikenzie Labs

Telegraph Decoder Kit by Spikenzie Labs

Telegraph Decoder Kit by Spikenzie Labs

Getting Started with Arduino Kit v3.0

Getting Started with Arduino Kit v3.0

Getting Started with Arduino Kit v3.0

Make: Getting Started with Soldering Kit

21 Responses to Sous Vide Immersion Cooker

  1. jdinto99 on said:

    Foodsaver is a very common brand of vacuum sealer that works well. You want the type that draws air out of the bag and then heat-seals it, not the type that uses a zipper bag with a one-way valve on it. Costco has a feature-rich model for about $150, but I was able to score a comparatively simple model for $26 by watching slickdeals.net.

    Reply ↓
  2. Matt Ponkey on said:

    Can you link a good one to buy?

    Reply ↓
  3. Scott Heimendinger on said:

    Also look out for the 20% off coupons to Bed Bath and Beyond. That’s the best price I’ve seen for a FoodSaver brand.

    I strongly advise you not to waste money on the cheaper models or the models that use a zipper bag. Nothing but frustration, in my experience.

    Reply ↓
  4. Scott Heimendinger on said:

    Yes, http://www.amazon.com/dp/B002PIM3R8/?tag=seattlefoodgeek-20. It has a slighly different pin configuration, but I’ll be updating the build on my blog with specific instructions for that model soon.

    Reply ↓
  5. Scott Heimendinger on said:

    Max, great solution! Any chance you could email or post a photo?

    Reply ↓
  6. Matt Ponkey on said:

    That sounds like an awesome idea. Could you post a photo of how it looks and any updated instructions.

    Reply ↓
  7. Ethan on said:

    The notes on this PID state that it works with a K type thermocouple. It doesn’t state that it will work with a pt100 probe. Will the immersion circulator need to be modified to use the K type thermocouple?

    Reply ↓
  8. John on said:

    I made mine with an outlet instead of the immersion heaters for that very reason. I ran the ground from my plug to the outlet, so the controller isnt grounded, but whatever I plug in can be.

    Reply ↓
  9. John on said:

    On second thought though, the whole grounding thing is a bit of a wash for me. The immersion heaters aren’t three pronged, my slow cooker isnt three pronged, and neither is my hot plate, so…

    On a side note, I have a chuck roast cooking right now, should be ready tomorrow evening!

    Reply ↓
  10. Guillaume Filion on said:

    Here’s an implementation that I’m much more comfortable with:

    http://youtu.be/6mMsusYW6qo

    In fact, I’m heading to the electronics store to get the parts to make it! :)

    Reply ↓
  11. Peter Funk on said:

    Excellent idea. Gluing the 1/4″ nut was a total failure for me. Melting a T-Nut into the plastic around the hole I drilled worked like a charm!

    Reply ↓
  12. Eric Chu on said:

    I think that’s due to one of the upper-limit alarms. Try changing the limits or try repeating what you did before and set it to a higher limit.

    Reply ↓
  13. Xuth on said:

    I should add that I drilled a 3/8″ hole near the top of the side of the cooler that I fed the heater cord, the pump cord and a flexible waterproof pt100 probe. I cobbled together an aluminum frame to mount the heater and pump to that just sits in the cooler in such a way that it can’t tip over. This allows me to put the lid on the cooler (keeping things well insulated) and doesn’t leave anything dangling precariously over the water. Adding a 3 or 5 amp fuse would be a good thing as well but I’ve not done so yet.

    Reply ↓
  14. Courtney Langford on said:

    did you figure out why it stayed at 40 ….if so could you tell me what to do in order to fix that problem

    Reply ↓
  15. Charles Barnard on said:

    Ah yes, the ‘new’ cooker, a variation on dropping heated rocks into pots.

    But like all appliances, the big problem is the amount of space they use up–either in the open or on the counter or in a closet. Most of the time it’s wasted cubic.

    Also, most have no good way to drain & clean them, and while those aren’t insolvable problems, they are a bit of PIA.

    So I thought about it for a bit and realized that every kitchen already HAS a waterbath, it’s just not rigged for temperature control (and it ought to be rigged for 25F-190F so you could heat or chill.)

    The waterbath is usually called the sink. Easy to fill, easy to drain, easy to access, easy to clean.

    All it needs is a heating/chilling unit and a thermostat control and a bit of insulation around the outside and perhaps a cover.

    When I get the thing designed & built I’ll post it.

    Reply ↓
  16. Matt Gitlin on said:

    I realize now that the pump doesn’t matter at all. Just as long as it is powerful enough for the capacity of water you want to push through the heaters.

    Reply ↓
  17. J N on said:

    Easy. Just make sure your PID, PUMP, and HEATING elements are rated for 220V. I am using a heating element originally rated at 1500W @ 220V. On 120V here in the US it will only put out about 750W with the reduced voltage.

    The PID called out above is good for nearly all international voltages. Just need to keep an eye out for the correct pump and heating elements then.

    Reply ↓
  18. Claes on said:

    Nice build!

    I’ve also made one of mine, but with a different design.

    http://www.lindens.nu/http_projekt/sous-vide/en.htm

    Reply ↓
  19. Ricky Fielding on said:

    Two of my three immersion heaters were duds (I was careful about not plugging them in without water) so I ended up buying a replacement water heater element. It’s not as portable, but it works like a charm.

    Reply ↓
  20. Richard Unger on said:

    Hi,

    I’m going to give this a shot – since I’m in Europe I won’t be able to use exactly the same parts, so I’m browsing around for suitable 220V alternatives.

    My question: I was wondering if there was any special reason to use 3x300W immersion heaters, rather than one 1000W model (or 2x500W)?

    Regards from Vienna,

    Richard

    Reply ↓
    • Ricky Fielding on said:

      Richard, I found that a single 1500W replacement for a water heater was the best. At least one of the immersion heaters I bought was defective. 1500W should raise the temperature of a 5 gallon bath by 60-70°F in an hour. You will have to be careful with the connections to the heating element since, at least on mine, the connections are open.

      Reply ↓

Leave a Reply

Fill in your details below or click an icon to log in:

Gravatar
WordPress.com Logo

You are commenting using your WordPress.com account. ( Log Out / Change )

Twitter picture

You are commenting using your Twitter account. ( Log Out / Change )

Facebook photo

You are commenting using your Facebook account. ( Log Out / Change )

Cancel

Connecting to %s

Join the MAKE Forum
Makershedad_DOTW_%20Makershields

// What's Trending

Raspberry Pi Design Contest
Raspberry Pi Design Contest
  • By: Nick Normal
  • Hits: 19474
Seventeen Sneaky Secret Hides
Seventeen Sneaky Secret Hides
  • By: Sean Michael Ragan
  • Hits: 4494
Teardrop Camper Trailer
Teardrop Camper Trailer
  • By: Werner
  • Hits: 2915
10 Things to Connect to Your Raspberry Pi
10 Things to Connect to Your Raspberry Pi
  • By: Alasdair Allan
  • Hits: 2580
Lost PLA Casting from 3D Prints
Lost PLA Casting from 3D Prints
  • By: Eric Weinhoffer
  • Hits: 1806
DIY 3D Laser Scanner Using Arduino
DIY 3D Laser Scanner Using Arduino
  • By: Ken Denmead
  • Hits: 1693
I Have a (Puzzling) Dream
I Have a (Puzzling) Dream
  • By: Gareth Branwyn
  • Hits: 1544
New Project: DIY 3D Laser Scanner Using Arduino
New Project: DIY 3D Laser Scanner Using Arduino
  • By: Ken Denmead
  • Hits: 1260

// What's Shared

A better way to slice a pumpkin
A better way to slice a pumpkin
  • By: Sean Michael Ragan
  • Shares: 42367
DIY Nerf Darts
DIY Nerf Darts
  • By: Adam Flaherty
  • Shares: 27186
100 Dollar Store Organization Ideas for Craft Rooms and Beyond
100 Dollar Store Organization Ideas for Craft Rooms and Beyond
  • By: Haley Pierson-Cox
  • Shares: 23042
In the Maker Shed: Minty Boost USB Charger
In the Maker Shed: Minty Boost USB Charger
  • By: Maker Shed
  • Shares: 22088
Mad’s Mouse House
Mad’s Mouse House
  • By: Meg Allan Cole
  • Shares: 13883
Lace Princess Crowns
Lace Princess Crowns
  • By: Meg Allan Cole
  • Shares: 13116
I Have a (Puzzling) Dream
I Have a (Puzzling) Dream
  • By: Gareth Branwyn
  • Shares: 10518
Play the Rings of a Tree Trunk Like a Record
Play the Rings of a Tree Trunk Like a Record
  • By: Matt Richardson
  • Shares: 10253

// Most Commented

Jason Poel Smith Picture
DIY Hacks & How To’s: Get Emergency Power from a Phone Line
  • By: Jason Poel Smith
  • Comments: 37
sample parts
Resin Casting: Going from CAD to Engineering-Grade Plastic Parts
  • By: Michal Zalewski
  • Comments: 36
Don't get me wrong, they're cheap and often get the job done, but they were made to not drive well. They were designed specifically in the early 20th century to cam out when too much force was applied. Now that we have torque-limiting drills this isn't a problem anymore, yet somehow we still use them.
Ten Tips for Screws and Screwdrivers
  • By: Michael Colombo
  • Comments: 27
We use the phrase "two by four" in common parlance, but did you know it's actually 3.5 inches wide? Don't make assumptions on size; always measure first.
Ten Tips for Better Measurement
  • By: Michael Colombo
  • Comments: 19
BrainMachineWorkshop
Is it a Hackerspace, Makerspace, TechShop, or FabLab?
  • By: Gui Cavalcanti
  • Comments: 19
E59A0674
Makers on TV: Big Brain Theory
  • By: Sabrina Merlo
  • Comments: 12
Arduino Yun
Arduino Announces New Wireless Linux Board
  • By: Andrew Terranova
  • Comments: 12
Screen shot 2013-05-08 at 12.56.44 PM
Grow: A Portable CNC Router System
  • By: John Baichtal
  • Comments: 11
MAKE
Trending Topics
About Maker Media

Make on Twitter Make on YouTube Make on Pintrest Make on Flickr Make on Facebook Stumble Make Magazine MAKE on Instagram MAKE on Google+

%d bloggers like this: