CupCake CNC build, part 6: Building the enclosure

3D Printing & Imaging Robotics
CupCake CNC build, part 6: Building the enclosure
IMG_9447-ajpeg.jpeg

It’s finally time to build the enclosure! The wax finish is fully cured, buffed out, and all the parts are ready for assembly. So, lets get on with the build.

IMG_9718.JPG

The first step is adding the bearing brackets to the middle panel. These screw on the bottom of the middle layer with the included M3 nuts and bolts.

IMG_9721.JPG

One in each corner, and… Done! Easy.

IMG_9725.JPG

Now it’s time to join the front and back panel to the middle. Again, using the M3 nuts and bolts. Be sure to make the back panel face inwards. The laser etching should be visible when looking into the CupCake CNC machine. Once completed, add the left, right, top, and bottom in the same manner.

IMG_9727.JPG

Now we need to assemble the Z-stage rods. It’s easy, but there’s some important prep work to do first. The threaded rod has some metal “bits” in the threads that need to be removed.

IMG_9729.JPG

The easiest method is to put some tape on one end of the threaded rod and insert it into an electric drill. Next, add a little oil, and while slowing turning the rod, use a paper towel to clean out all the debris. Done!

IMG_9731.JPG

Now it’s time to assemble the Z-stage threaded rods. First you add (1) 8mm nut onto the threaded rod, followed by (1) 608 bearing, and another 8mm nut. Use (2) wrenches to tighten the bearing onto the threaded rod.

IMG_9734.JPG

Next, add another 8mm nut on the other end. This one is used to hold the Z-stage in place. It should be screwed down a few inches to stay out of the way. Then you can add another bearing sandwich like you did on the other end. Note: Do not tighten them up yet!

IMG_9735.JPG

Next, place the Z-stage threaded rod into the four holes in the top of the enclosure and into the holes in the “middle” layer.

IMG_9740.jpg

You need to adjust the top-bearing sandwich so that the bearing sits just at, or slightly below, the top layer of the CupCake CNC. It is very important that the bearing sits flush! Double and triple check it!

IMG_9745.jpg

Once all the bearings sit flush, you can add the Z -stage brackets. Use (1) screw on each cover until you know there is no play, or any friction, on all the threaded rods.

IMG_9747.JPG

When it’s perfect, go ahead and add the rest of the screws.

IMG_9750.JPG

Next up is adding the power supply. Unfortunately, it didn’t fit the laser-cut opening. I had to make the opening slightly larger to accommodate the power switch and plug. Start by cutting a section of wood out from around the switch area. You can eyeball the exact amount fairly easily.

IMG_9752.JPG

Also, you will need to cut a small notch out of the side to allow more room for the plug. Place the power supply behind and mark the area with a pencil. Then, using a craft knife, carve a small semi circle.

IMG_9755.JPG

Once those modifications are made, attach the power supply to the laser-cut plywood. Next, attach the entire assembly to the enclosure using the same bolt and screw method used on all the other panels.

IMG_9757.jpg

Now, feed the cables through the opening on the right hand side of the enclosure.

IMG_9759.jpg

Done! The enclosure is complete and ready for some electronics. Speaking of which, let’s go ahead and add some stepper motors while we’re at it!

IMG_9762.JPG

First, we will install the X-axis stepper motor. Start by attaching one of the small silver pulleys to the stepper motors shaft. The shaft of the motor should be flush with the top of the pulley. Tighten down the setscrew and you are ready to install it into the enclosure.

IMG_9763b.JPG

Now you can mount the X-axis stepper motor to the middle section of the enclosure with the (4) shorter M3 bolts. The bolts thread right into the stepper motor. Easy!

IMG_9766.JPG

Next up, it’s time to install the Z-stage stepper motor. This stepper used the black pulley from the kit. Note: Do not tighten this pulley yet. You may need to adjust the height a bit in the next step.

IMG_9775.JPG

Now we can go ahead and add all the pulleys to the Z-axis threaded rods. These pulleys are put on upside-down compared to the one installed on the stepper motor.

IMG_9776.JPG

Also, you can add the tensioning pulleys that were made in part 5 of this build series. They are installed on each side of the stepper and keep the correct tension on the belt. Finally, add the belt and adjust the tension. It should be tight, but not too tight. I know that seems a bit vague, but you’ll know when it’s right.

IMG_9770.JPG

The final step is to make sure the height of all the pulleys is correct. As you can see in the image above, the belt sits perfectly inline with the pulleys, especially the one mounted to the stepper motor. Adjust all the pulleys into alignment, and then tighten all the set screws.

And, DONE! We’re finished building the enclosure. Next up in the series: Building the Y-stage.

Ask questions! Do you want to see a better picture of a particular part, a different camera angle, a video perhaps? Maybe you have a suggestion for a cool mod or hack? Let me know in the comments. I’ll try to answer them as best as I can. Thanks!

Want to know when my next build entry is done? Follow me on Twitter @devinck!

Build history:

    IMG_0297.JPG

    Having just arrived home from a quick trip to the hardware store, I was pleasantly surprised to see a large, unmarked, cardboard box sitting on my front steps. This isn’t an uncommon event, since I am constantly checking out cool products and projects for the Maker Shed, however this box was a bit larger than normal.

    Oh wow, it’s the CupCake CNC kit from MakerBot Industries! I’d ordered it weeks earlier and had completely forgotten about it. (The truth is out: I have an atrocious memory, sad but true.)

    IMG_9117.JPG

    And so the adventure begins! I’m going to document my “out of box experience” with a MakerBot. How many posts will the series be? I’m not sure since I’ve never built one. How often will I post about the build? Again, not sure, but I’ll try to do at least one a week, maybe more, it all depends on how much free time I have between all my other maker-ly projects.

    A little background: My CNC experiences

    IMG_9098.jpg

    I’ve been tinkering with CNC for about 10 years, and consider myself an enthusiast, not an expert. I do own a few CNC mills, routers, and lathes. I have retrofitted old mills, and even build one from scratch. Pictured above is my mobile CNC machine, dubbed the “MobileC.” I stuffed all the components into a mobile tool cart so I could bring it to hackerspaces, workshops, and events, all in the hopes of helping out fellow makers.

    4077680467_119b920a82_b.jpg

    The mill is a Sherline 5400 that I retrofitted for CNC. Also, I added a few extra parts to make it even more useful. It has a longer reach, thanks to the headstock spacer block on the column, and a larger table that I simply mounted to the stock table. It’s a sweet machine. I love my little Sherline!

    4077673575_d8fc55c17d_b.jpg

    All the electronics are housed in the cart too! There is a 19″ LCD monitor, wireless keyboard and mouse, desktop computer, and CNC controller. It’s a tight fit, but it works perfectly. There is even an extra full-size drawer for tooling and accessories.

    IMG_9110.JPG

    I’m thinking of replacing the computer, keyboard, and mouse with an HP TouchSmart, but I have to save a few more pennies for that upgrade.

    Does anyone want to know more about my MobileC? Let me know in the comments. After I build my CupCake CNC, maybe I should do a series of articles on CNC machining?

    Disclosure:

    I purchased the CupCake CNC kit with my own hard-earned cash. I waited several weeks for it to arrive, just like everyone else that placed an order. No favors, no freebies! Why did I buy one? Well, for two reasons.

    • Reason #1 – I like what MakerBot Industries is doing for the open source community and open manufacturing, so I wanted to support them!
    • Reason #2 – I am going to document the build for Make: Online, and if I like it, I’ll let you know, and if I don’t… well, I’ll let you know that too! No biased reviews here.
    • Reason #3 – I am a CNC junkie, and I had to have it, even if my wife was questioning whether I really needed another machine in my studio! “Ha!” I said, “You can never have too many machines!” Oops, only two reasons, right?! :)

    Questions & suggestions:

    Ask questions! Do you want to see a better picture of a particular part, a different camera angle, a video perhaps? Maybe you have a suggestion for a cool mod or a hack? Let me know in the comments. I’ll try to answer all of them as best as I can. Thanks!

    Build history:

20 thoughts on “CupCake CNC build, part 6: Building the enclosure

  1. David Hall says:

    Very nice set of instructions!

    The pulley for the z axis steeper motor will not slide on. I do not want to force it. I tried some WD-40 but no luck. I can press the pulley on for about 2-3 mm and then it will go no further.

    Ideas?

    Dave

    1. Marc de Vinck says:

      Thanks!

      Yes, the pulley is really tight…REALLY tight! First, make sure the set screw is completely out, next, open up the hole on the pulley a bit with some fine sand paper wrapped on a wooden dowel or small file. Don’t do it too much! The tolerance on the pulley and stepper isn’t critical….but it should be “sloppy”. Sand it down just a bit and try it again.

      Also, try pressing the pulley on with even pressure. Maybe try pressing the stepper onto the pulley (i.e. put the pulley on a flat surface and press the stepper onto it)

  2. Rainor says:

    Hello – I was thinking that due to the softness of the wood and the relative size of the M-Bolts, shouldn’t the kit come with flat washers?

    Over time the motors or other stress points might losen up as the heads pull-through the plywood. I’m thinking of the 4 bolts in the 2nd to last photo IMG9776.JPG

    Nice looking project so far! I look forward to the next part :-)

    1. Marc de Vinck says:

      That’s a good point. I have the same concerns….and adding some additional washers is a great idea. Only time will tell.

      Next post is going up tomorrow!

    2. cdesfablab says:

      We thought the same thing about the cap head screws getting buried so we used M3x16 flange button head socket head screws wherever possible. Not only does this address the compression issue, but it makes for a cleaner aesthetic overall. Much less trouble than messing with ~150 little washers. Now to find square nuts for the T joints on the next build.

      http://www.mcmaster.com/library/20080923/92137A258L.GIF

  3. zgrinch says:

    Like the title says, I just discovered Make about a month or so ago. This is the most interesting site on the net. The possibilities are endless. I found your build irresistable and you now have a fan as I cannot wait for the next post. It is my hope that Make will start a beginners area for those of us who have soooo much to catch up on. I get almost all of what is done on this site with the exception of the programmming, which really isn’t applicable to this series. Anyway, great work, great build, cannot wait to see what you MAKE first with this machine, have you given it any thought? Later Zgrinch

  4. john says:

    I’d appreciate a photo of the nut/washer order that you used for the z axis tensioning pullies.
    Cheers!

    1. CupCake CNC build, part 6: Building the enclosure Maker Shed says:

      Sure, I have to take it apart to shoot it…but I will reply here, and post a link to my flickr photo set.

    2. CupCake CNC build, part 6: Building the enclosure Maker Shed says:

      OK, no pics yet, but I juts checked. It has 2 nuts under the pulley, and another to secure it to the CupCake CNC….that’s it. I’ll take a pic, but that should help for now.

      1. Gaffetape says:

        That will help for now indeed. Thanks!

Comments are closed.

Discuss this article with the rest of the community on our Discord server!
Tagged

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK